Q3) The following reading was taken from the performance test of single cylinder four-stroke engine with 250 mm bore and 400 mm stroke: indicated mep 7.5 bar, engine speed 250 rpm, net load on the brake 1080 N, effective diameter of the brake 1.5 m, fuel used per hour 10 kg, calorific value of the fuel 44300 kK/kg. calculate : (1) Indicated power (2) Brake power (3) Mechanical efficiency (4) Indicated thermal efficiency State any necessary assumptions for your analysis. 1)

Q3) The following reading was taken from the performance test of single cylinder four-stroke engine with 250 mm bore and 400 mm stroke: indicated mep 7.5 bar, engine speed 250 rpm, net load on the brake 1080 N, effective diameter of the brake 1.5 m, fuel used per hour 10 kg, calorific value of the fuel 44300 kK/kg. calculate : (1) Indicated power (2) Brake power (3) Mechanical efficiency (4) Indicated thermal efficiency State any necessary assumptions for your analysis. 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An engine undergoes the brake power testing in an brake rope dynamometer running at 8000 rpm and experience a torque of 500 N-m, how much brake power generated by the engine?
Please solve the question quickly
The calculation of friction loss from sudden expansion and contraction uses a. Continuity equationb. Steady-flow momentum balance equationc. Bernoulli equationd. All of these
rev/min Q2: a/ an engine producing 12 kW power at 3000 rev/min is fitted to a vehicle with a mass of 700 kg. if the rolling resistance is 130 N determine the maximum gradient this vehicle could climb in top gear with a 4.5:1 final drive ratio, a transmission efficiency of 70%, and a wheel radius of 0.28 m. أدخل نص
Please solve the Below problem using 'Design data book'. And while solving problem add some table or figure reference number before taking each reference value. If answer is right then I will give you upvote/like.
A) If we consider a transmission ratio 1 to 5, in the arrangement of pulleys shown. and the tangential speed in the shaft (diameter of 30mm) where the driving pulley is coupled is 1.5 m/s. What is the rotational speed of the driven pulley (in rpm)? B) From the previous exercise. What is the length of the transmission band (belt) calculated in the previous exercise? Motriz 0.30 m 1.5 m uc=0.35 -0.30 m- 0.40 m Movida -0.30 m 0.30 m d=0.10 m e-0.05 m
An engine system of 3 msin components in a series sll having the same reliability. Determine the level of reliability required for each of the components if the engine is to have a reliability of 0.995. Round answer tob4 decimal places e.g. 15.2512
A two-stroke direct injection diesel engine has a displacement of 23 liters. The engine has a maximum output of 880hp at 2245 rpm and is derated to 321.6kW at 1800 rpm for industrial use. 1. What is the bmep for each of these types in bar? 2. Convert also the pressure in psi.
5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody Diagram 0.1 0.09 Transition Region 0.08 0.07 0.05 0.04 0,06 0.03 0.05 0.02 0.04 0.015 0.01 0.03 0.005 0.002 0.001 5x10-4 2x10-49 10-4 5x10-5 10-5 5x10-6 10-6 Friction Factor 12---- Laminar Flow 64 Material Concrete, coarse 0.25 0.025 Concrete, new smooth Drawn tubing 0.0025 Glass, Plastic Perspex 0.0025 Iron, cast 0.15 Sevens, old 3.0 0.1 Steel, mortar lined Steel, rusted 0.5 Stoel, structural or forgod 0.025 Water mains, old Friction Factor=AP. 1.0 Smooth Pipe 3000 10³ 10¹ 105 106 107 108 Reynolds Number, Re - Vd P a) The lines for different relative roughness in the turbulent regime correspond to Darcy-Weisbach model b) The lines for different relative roughness in the turbulent regime correspond to Nikuradse model c) The lines for different relative roughness in the turbulent regime correspond to Hazen-Williams model d) The lines for different relative roughness in the turbulent regime…
Q1/ Select the best answer for the following : 1-In a four stroke engine, * .the piston accelerates & decelerates in each crank revolution (A) once O (B) twice O (C) 4 times O (D) none of these O * ?What is the capacity of one cylinder in a 5-litre V8 engine -2 (A) 1.625 L O (B) 4 L O (C) 0.525 L O D) 0.625 L O The flywheel of an internal combustion engine maintains the smooth-3 rotary motion of the (A) camshaft O (B) crankshaft (D) rear wheels. (C) gearbox C
O Snociogr O Facebook ology.com/common-assessment-delivery/start/4717647553?action=onresume&submissionid=583526132 ube Maps 9 of 10 0127 I 01:3 A single-cylinder, double-acting, four-stroke cycle engine consists of O Two power strokes for every revolution of the crankshaft O One power stroke for every revolution of the crankshaft O One power stroke for every two revolutions of the crankshaft O none of these 1 2 3 4 5 6 7 8 9 10 Ne TermE of Use
7.6 A carburetor, tested in the laboratory has its float chamber vented to atmosphere. The main meter is Iystem is adjusted to give an air-fuel ratio of 15:1 at sea level con ce s The pressure at the venturi throat is 0.8 bar. The atmospherie fie rsure is 1 bar. The same carburetor is tested again when an air eleaner is fitted at the inlet to the carburetor. The pressure drop to air cleaner found to be 30 mIi of Hg when air flow at sea level condition is 2 e coellicient of flow, caleulate (1) !, claroat pressush is fitted and (ii) air fuel rat io when the air cleaner i fitted. Assumingn dp and constant a the air cleaner