Q3) Show the complete logic of the carry flip-flop E in the basic computer.

(Practice) Determine the values of the following integer expressions: a.3+46f.202/( 6+3)b.34/6+6g.( 202)/6+3c.23/128/4h.( 202)/( 6+3)d.10( 1+73)i.5020e.202/6+3j.( 10+3)4

_____ predicts that transistor density will double every two years or less.

(For review) List the three repetition statements provided in C++.

(Civil eng.) Modify the program written for Exercise 9 to determine the maximum load that can be placed at the end of an 8-foot I-beam, shown in Figure 2.21, so that the stress on the fixed end is 20,000lbs/in2. Use the fact that this beam’s rectangular moment of inertia is 21.4 in4 and the value of c is 3 in.

(Chemistry) a. Determine the final units of the following expression, which provides the molecular weight of 1.5 moles of hydrogen peroxide: 1.5moles34.0146grams/mole b. Determine the final units of the following expression, which provides the molecular weight of 5.3 moles of water: 5.3moles18grams/mole

(Electrical eng.) a. Write, compile, and run a C++ program that calculates and displays the value of the current flowing through an RC circuit (see Figure 3.19). The circuit consists of a battery connected in a series to a switch, a resistor, and a capacitor. When the switch is closed, the current, i, flowing through the circuit is given by this formula: i=(EIR)et/RC Eisthevoltageofthebatteryinvolts.Risthevalueoftheresistorinohms.Cisthevalueofthecapacitorinfarads.tisthetimeinsecondsaftertheswitchisclosed.eisEulersnumber,whichis2.71828( roundedtofivedecimalplaces). Using this formula, write, compile, and run a C++ program to determine the voltage across the capacitor shown in Figure 3.19 when t is 0.31 seconds. (Note: The value of RC is referred to as the system’s time constant.) The program should prompt the user to enter appropriate values and use input statements to accept the data. In constructing the prompts, use statements such as “Enter the voltage of the battery.” Verify your program’s operation by calculating by hand the current for the following test data: Testdataset1:Voltage=20volts,R=10ohms,RC=0.044,t=0.023secondsTestdataset2:Voltage=35volts,R=10ohms,RC=0.16,t=0.067seconds b. Check the value computed by your program by hand. After verifying that your program is working correctly, use it to complete the following chart:

(Practice) Determine the value of the following expressions, assuming a=5,b=2,c=4,d=6,ande=3: a.abb.a!=bc.db==cbd.ac!=dbe.db==cef.!( ab)g.!( abc)h.!( cba)i.bca

(Automotive) a. An automobile engine’s performance can be determined by monitoring its rotations per minute (rpm). Determine the conversion factors that can be used to convert rpm to frequency in hertz (Hz), given that 1rotation=1cycle,1minute=60seconds,and1Hz=1cycle/sec. b. Using the conversion factors you determined in Exercise 7a, convert 2000 rpm into hertz.

(Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given by this formula: d=wx224EI(x2+6l24lx) d is the deflection at location x (ft). xisthedistancefromthesecuredend( ft).wistheweightplacedattheendofthebeam( lbs/ft).listhebeamlength( ft). Eisthemodulesofelasticity( lbs/f t 2 ).Iisthesecondmomentofinertia( f t 4 ). For the beam shown in Figure 5.15, the second moment of inertia is determined as follows: l=bh312 b is the beam’s base. h is the beam’s height. Using these formulas, write, compile, and run a C++ program that determines and displays a table of the deflection for a cantilevered pine beam at half-foot increments along its length, using the following data: w=200lbs/ftl=3ftE=187.2106lb/ft2b=.2fth=.3ft