Q3: Select the correct answer. 1- Which one of the following statement in MATLAB determines the state gains(K1 K2 .) for the repeated design poles? * K=acker(A,B,poles) O K=acker(B,A,poles) O K=place(B,A,poles) O K=place(A,B,poles)

Q: If the value of the damping ratio or damping factor is 1.5, then the system is an overdamped system.

A: An overdamped system is a system which slowly reaches to the equilibrium state

Q: 16. Determine the output waveform in Figure 3-85 and draw the timing diagram. A

A: The given gate is "NOR" gate. Truth table for NOR gate: X Y (X+Y)' 0 0 1 0 1 0 1 0 0 1 1…

Q: Describe how to combine more than one multiplexer

A: Describe how to combine more than one multiplexer The term Multiplexer which is commonly called as…

Q: input:     -65 44 Input:    -37 -39 H -25 -5 -54   both fail to run

A: The code starts by importing essential Java libraries, laying the groundwork for user interaction…

Q: CK Q Fig Bl LE CK do it b) What type of device is shown in Fig. B1 if the waveforms illustrated are…

A: A stable multivibrator is an electronic circuit that generates a continuous square wave or…

Q: Q3 Design 3-bit flash Analogue to Digital Converter Circuit, where reference voltage Veet (8V), find…

A:

Q: DPI stands for Dots Per Inch.

A: Let's understand what is DPI: Dots per inch (dpi) is a measure of the sharpness (that is, the…

Q: Explain bit mask briefly. What if you press the Enter key when the focus is on a Button control?

A: Introduction: To access certain bits in a byte of data, bit masks are utilised.

Q: Horizontal block Also called the voltage base true False O

A: Horizontal block called the time base vertical block called the voltage base

Q: Laplace transform of 1 signal is represented as G(s) g2 Unit Parabolic Unit Ramp O Unit Step Unit…

A: I have provided answer in step2.

Q: design a four way light control then impiement the design using A-PAL realization B-VHDL code

A: Solution:--   1)As given in the question it is required to provide the VHDL code for the given…

Q: Digital Electronic

A: Step 1:jk flipflop:A JK flip-flop can be constructed using NAND gates. Here's how you can do it:1.…

Q: 91 a, b→c 92

A:

Q: nen the loop in the PLL is locked, what is the difference in frequency detected by the phase…

A: PLL is Phase Locked Loop

Q: To control the operation of the decoder there may be one or more enable inputs select inputs output…

A: The answer is given below step.

Q: The definition of Vertical Micro Code

A: The definition of Vertical Micro Code: The micro-operations in vertical microcode are organised…

Q: Name two functions of a camera control unit

A: A live television transmission chain usually includes a camera control unit (CCU). It powers the…

Q: The EGA does not support this position. What is the reason for the addressable display on all…

A: GIVEN: The subject is EGA's lack of support. Display that is addressable at all points

Q: How is a vertical-coding control unit assembled?

A: The assembly of a vertical-coding control unit is a fascinating process worth exploring. This…

Q: The percentage resolution of 10 bit DAC is more than 12 bit DAC Select one: True False

A: Refer to step 2 for the answer.

Q: please create the schematic on KiCad software for this circuit

A:

Q: What makes a vertical-coding control unit?

A: Vertical coding in control units refers to a methodology employed in computer architecture for micro…

Q: a) create a digital circuit of the simplified expression.  b) determine the expression in regards…

A: The Boolean expression for the given circuit is, F=(AB+C').(A+C) The simplified expression for the…

Q: What is DSWD in 500 word

A: ANSWER : The Department of Social Welfare and Development (DSWD): The Department of Social Welfare…

Q: Describe how GPSS GENERATE operator works.

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: The quantization stage of the ADC having an error (power) less than

A: In pipeline ADC, in order to get integral nonlinearity (INL) <1LSB, we need to make sure that the…

Q: What type of device is shown in Fig. B1 if the waveforms illustrated are present at its CK and Q…

A: Answer : 1. it is BI-STABLE

Q: Q5. According to the figure below, calculate the output of the digital circuit and write the truth…

A: Explaining the gates used in the question:   In the AND gate, the output is "true" when both inputs…

Q: In rectification process, T is Select one: a. amplitude of signal b. none of above c. phase of…

A: Rectification process take use of devices such as diodes, transistors, converters etc. to convert an…

Q: How are vertical-coding control units built?

A: Vertical-coding control units are an essential component in various technological systems. These…

Q: The serial data input waveform and data selectors are shown in Fig. (8-6). Determine the data-output…

A: The truth table which determines the outputs of 1-to-4-line demultiplexer is as follows:

Q: Design a Majority function

A: Majority function It is a function from n inputs to one output. The value of the operation is false…

Q: An unconnected TTL input acts as a LOW. (T or F)

A: Lets see the solution.

Q: CD Track Spiral and Track Enlargement

A: Given : -   CD track spiral and track enlargement  as shown in figure given    Need to explain the…

Q: Convert the following eight-bit two's complement number to decimal: 11002":

A: Here have to determine convert 2's component to decimal.

Q: Explain how you can use PIC16F84A MCU to multiply two hexadecimal numbers: Flow chart

A: Here is how you can multiply two hexadecimal number:

Q: In a multiplexer the output depends on its Select one: O a. Data inputs Ob. Select inputs Oc. Select…

A: Below I have provided a solution for the given question.

Q: Draw an 8 to 1 multiplexer which uses two of 4 to 1 multiplexer and a 2 to 1 multiplexer

A:

Q: How many select lines are required for a 1-to- 8 demultiplexer ?  a) 1  b ) 2  c) 3  d ) 5

A: Task :- Choose the correct option for given question.

Q: Q1: Determine all the output waveforms for the 74HC195 when its input signals are shown below CLK…

A: