Q3: In the orifice meter exper we found the following data of sample: The volume of water through 15 second is 315 mL, the diameter of the prifice meter is 6mm, and the height of the tank in (mm) is 300 the vertical distance of the needles (2) and (7) is 3 and 9 cm respectively. Find for two the needles listed above: 1-Cofficient of discharge 2- Coefficient of velocity. 3- Coefficient of contraction. ontracti

Q3: In the orifice meter exper we found the following data of sample: The volume of water through 15 second is 315 mL, the diameter of the prifice meter is 6mm, and the height of the tank in (mm) is 300 the vertical distance of the needles (2) and (7) is 3 and 9 cm respectively. Find for two the needles listed above: 1-Cofficient of discharge 2- Coefficient of velocity. 3- Coefficient of contraction. ontracti

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system curve for a water supply system is shown in the figure below (i.e., red curve). If a 7-inch pump is operating at 1160 rpm, what will be the discharge of water through the system in GPM? Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 HEAD IN FEET 30 25 W 20 10 5 L/SEC 5 7.00" (178mm) 6.75" (171mm) 6.50" (165mm) 15 6.25" (159mm) 7.25" (184mm) O 150 GPM Laco O 350 GPM O 450 GPM O 250 GPM 10 Model 4075 FI & CI Series 15 70% 20 "Dede de 088 A. 25 REQUIRED NPSH 90 1160 RPM November 1, 2010 TM 90- N 00 30 8800 877 1HP(.75KW) de (5 60% ox 35 -10% 5% Tolo 10. 3HP(2.2KW) 2HP(1 5KW). 15HP(1 1KW). CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE 45 LOWONG FEET 15 12 9 6 0 6 5 + 2 1 750 NPSH HEAD IN METERS 45 36 OG KPO 27 18 -9 -70 -60 -50 -40 20 10 -0 HEAD IN KILOPASCALS
THE PROBLEM IS FROM THE BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD.
Q4/A- The mass of the filter is 25.3046 gm. after 20 min the filter mass will be 25.4112 gm. with volumetric flow is 5.2 m 3/hr. What is the concentration of pollutant after one day
Calculations involving retention time involve the following formula, T =, where V is volume and Q is flow rate. Often times, you will be required to calculate the volume of more than one tank and determine a rate of flow, given a total retention time. Tank 1 Tank 2 Let's assume that the total retention time for the entire system is 55 minutes, and we want to know the inlet flow, given the dimensions of tank 1 are : 14m x 10m x 3 m, and tank 2 are: 5m x 10m x 3 m. Calculate the inlet flow.
pllllllllllllease solve question 1
water flows through 30 mm internal diameter pipe at atmospheric pressure. pitot tube measures the velocity of water at the center of pipe as shown in the fig. the pressure difference between the impact tube and the static tube is 20cm of carbon tetrachloride (density: 1600 kg/m³). calculate the volumetric flow rate through the pipe in cubic meter per hour. velocity of water is cp.
4
1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
None
Toplam basınç göstergesi Manometre Vana Venturimetre Debiölçer Hazne Pompa Manometre=Manometer Venturimetre=Venturimeter Debiölser-Flaw meter Vana=Valve Pompa=Pump Hazne=Tank Toplam Basınç Göstergesi =Total Pressure Gauge It is desired to display the flow in the venturimeter, How can you determine this? Explain bY. explaining the method vou bave chosen.
A pitot-static probe is used to determine the flow velocity by measuring the differential pressure as shown in Figure 7. The pressure difference sensor used in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/v. i. Derive pitot formula to obtain flow velocity from Bernoulli equation, ii. Calculate the pressure difference inside the system, iii. Determine the velocity inside the system if the the fluid is water, and iv. Explain the cause that / ontirbute to inaccurary in the velocity reading. Fluid Flow, V Stagnation Static pressure pressure Pi-P2 Figure 7: Pitot static probe
%3D Find the pressure in KN/m2 at the center of pipe A. T = 10°C. Oil (S = 0.85) Water 90 cm 150 cm Water 30 cm Mercury (S = 13.6) to 30 cm