Q3- Find H and the pressure gage P as shown in Fig. 125 mm d H 75 mm d 175 mm 100 mm d Hg (13.57)

Q: Water at 10 Cflows from a large reservoir to a smaller one through a 5-cm diameter cast iron piping…

A: Given Diameter of the pipe = 5 cm = 0.05 m Flow rate = 6L/s Density = 999.7 kg/ms Friction…

Q: 4.18 What is the composition, in atom percent, of an alloy that contains 44.5 lbm of Ag, 83.7 lb,m…

A: Given data:         mass of Ag= MAG= 44.5 lbm         mass of Au= MAU = 83.7 lbm         mass of Cu…

Q: Link 4 moves to the right with constant velocity of 75 ft/s. Using the graphical method, find VB,…

A:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Ql. The bracket…

A:

Q: Problem 4. A cork ball (SG = 0.21) with a diameter of D = 0.30 m is tied to an object on the bottom…

A:

Q: In the figure, one end of a uniform beam of weight 480 N is hinged to a wall; the other end is…

A:

Q: 1. Two blocks, of masses M = 2.3 kg and 2M are connected to a spring of spring constant k = 180 N/m…

A:

Q: An isentropic air compressor takes 150 m/min of air in at 10°C and 100kPa and compresses it to 1000…

A: Given: Flow rate (Q)=150m3/min Inlet temperature T1=10°C or 10+273=283K Inlet pressure P1=100kPa…

Q: 11. A diatomic gas (y 1'4) does 200 J of work when it is expanded isobarically. Find the heat given…

A: Data given -  Diatomic gas Y = 1.4  W = 200 J  Isobarically

Q: A piezoelectric type accelerometer has a sensitivity of 100 mV/g. The transducer is subjected to a…

A:

Q: Figure Q4 shows a rod of negligible mass whose ends has to particles A and B which slides along the…

A: Therefore the position of center of mass will be at distance of “3L/4” from the end “A” and at…

Q: The process of reheating of the martensitic steel

A: Given; The process of reheating of the martensitic steel to reduce its brittleness without any…

Q: Solve the following model of spring mass system for the given damping coefficients: u"+bu '+u =…

A: Differential equation,u''+bu'+u=sinmtu0=2u'0=0

Q: The main disadvantage of mechanical power systems is attributed to? O Complex construction O…

A: if we talk about any mechanical device, whether it is an small bicycle or a power plant, all the…

Q: Calculate the per meter (of length) pressure drop (units: kPa) associated frictional losses (only)…

A:

Q: 2-69. The tapered settling tank is filled with oil. Determine the resultant force the oil ex- erts…

A:

Q: 3.44 The landing gear of an airplane can be idealized as the spring-mass-damper system shown in Fig.…

A:

Q: determine the minimum preferred size diameter.

A: Given: FOS=3  T2=0.15T2 To determine: The minimum diameter using distortion energy theory

Q: 3.6 m R 1m 1.2 m 2.5 m 3m The banner has a density of 670 kg/m and is 6mm-thick. The pipe has the…

A:

Q: Convert 589 mm to m.

A: Given Data : Length (L)=589 mm

Q: In the mechanism, as shown above, the crank OA rotates at 20 rev/min. anticlockwise and gives motion…

A:

Q: A dam on a river is built so that the wall facing the water is shaped like the region above the…

A: Given:The density of water is .The equation of curve is .The equation of line is .The water level is…

Q: 5. The semicircular gate is hinged at point A. What is the necessary force P needed to hold the gate…

A: The required force P. Given: The radius of the gate is R=15-8=7 ft. FBD: The free-body diagram of…

Q: 4. (a) Determine the reactions at supports A and E and the maximum tension in the cable in Figure.…

A: In a cable carrying a distributed load cable hangs in a shape of curve internal force is tension…

Q: A rigid bar the fiqure . Cons fruct the the deg rees of freedom díffuse , Supporied by a massless…

A:

Q: Solve for the tensions 45 50 g

A: Given: W=50 g Consider the Free Body Diagram:

Q: For the composite area shown below, determine the moment of inertia about the horizontal centroidal…

A: Data given- I section  Base = 180 mm  Height = 160 mm

Q: In figure Shown, felocity at Section-1, is 1.7 and density of water slog is 1.94 Sa. Neglect losses,…

A: Data given - Velocity at section 1 = 1.7ft/s Density of water = 1.94 slug/ft3 To determine - h= ?

Q: 4/1 Determine the force in each member of the simple equilateral truss. Ans. AB = 736 N T, AC = 368…

A:

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A = 65 B = 43

A:

Q: A cantilever beam of length 100-in carries three loads P1, P2 and 15 kip as shown. Choose distances…

A:

Q: Consider the truss shown in (Figure 1). Suppose that Fi = 4.5 kN and F = 6 kN. After the truss is…

A: Given dataForce F1 = 4.5kNForce F2 = 6kNTo determine the forces in the members BC HC and HG