1 A block rotates angle o about the 13- write down its deformation and obtain the deformation gradient show that the volume change is zero. axis. an

Q: Vrite a complete program to mill around the part. The endmill is .500 diameter, and yo nt to leave…

A:

Q: B1. A snowboarder rides over a jump (see the sketch below), where the launch ramp is at an angle of…

A: (1) Consider the path from take off point to start point of landing. Apply kinematic equation in…

Q: You need to design a clock using a DC motor that has a constant speed of 3000 rpm. Determine: How…

A: - to design a clock using a DC motor that has a constant speed of 3000 rpm. N = 3000 rpm

Q: Processing times (including setup times) and due dates for six jobs waiting to be processed at a…

A:

Q: If angular acceleration of pulley A is equal to 5 rad/s. The angular acceleration of C in rad/s is

A:

Q: The output of a certain machine can be increased if it undergoes a major overhaul now and it will…

A: P = $20,000 (P/A, 15%, 5)    = $67,044 finding A when given F, Given a future sum of money, F, how…

Q: 6. Why USM the slowest in terms of rate removal among the three electrical energy? processes ?

A: The USM is slowest due to the following reason:-

Q: why

A: Equating moment at A to find force in rod BC.

Q: The machine design has stated that a 2.5 kW electric motor with an input speed of 1000 RPM is needed…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve part (d) for…

Q: Read and analyze the questions/statements. Choose and write the letter of the correct answer. 1.…

A: Given that a clay is pushed by an equal and opposite force (by hand) . Let cross section area be A .

Q: p (2/1) u S In (1/2) da

A: the given function is a special integral which can not be solved by ordinary elementary operations.…

Q: Give a steps by steps answer of the solution

A:

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

A:

Q: The machine preferred for producing 100 pieces

A: Given; Data shown is;   Conventional lathe and CNC lathe are in consideration for…

Q: .1- Answer two of the following: a) What are deference between hot forming and cold fo

A: Hi and thanks for the question. Since you have asked multiple questions. As per the honour code, we…

Q: 4. Differentiate machining gap and machining capabilities in ECM process ? 4

A: Electrochemical machining (ECM) is an electrochemical technique for removing metal. It's…

Q: 8-In lathe, the carriage and tail stock are guided on.. a) Same guideways. b) Different guideways.…

A: Solution:

Q: Fursan Inc. needs 300 kgs of a material per month (four weeks). It costs RO 10 to make and receive…

A: Given data: The optimum quantity per order can be calculated as,

Q: Given: Stress-Strain curve of a steel with an initial diameter of 8 mm and initial length of 35 mm.…

A:

Q: can i have it done in hand writing?

A: Given Data:

Q: During machining of aluminum work piece, the cutting process was achieved in begin with dry…

A:

Q: a) Horizontal. b) Vertical. c) Can't say anything. d) None of the mentioned.

A: To cut a t slot the cutter should move parallel to the surface of the workpiece

Q: 10. The manufacturing process shown in the figure below is called? a. Turning process. b. Spinning…

A: for the question asked

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.