Q3/ Answer ONE of following questions: A. Fill control register by suitable bits: • T2CON: TOUTPS3: TOUTPS0 --→1:3 TMR2ON ON T2CKPS1:T2CKPS0→Prescaler 4 CCPXCON Registers: Capture mode, Every Rising Edge. B. Pinpoint for pins PIC16F877A power pins • Transmitter and receiver pins for USART.

Q: Suppose you have a synchronous sequential circuit whose clock has a cycle time of 1800 ps (i.e., T.…

A: Given, =>Clock cycle time(Tc) = 1800 ps =>tpcq(Propagation delay clock-to-q )= 300 ps…

Q: The input/output lines of an I/O NMOS chip are driven by darlington pairs and hence are capable of…

A: Hello Student. Hope you are having a good time. I will try my best to answer your question.

Q: Write the VHDL code for the circuit shown in figure2. The circuit acts as support circuit for the…

A: The concrete RTN for shr relies upon a 5 bit register to hold the shift count.  It must load,…

Q: 1. Design a 32-bit counter that will either increment by 4 or load a new 32-bit value, D, on each…

A: GIVEN:

Q: Use counter 1 of 82C54 interval timer in order to generate a continous series of pulses which have…

A: 8254 programmable interval timer: 8254 is a designed solve the timing control problems in…

Q: Design an embedded C code, based on STM32F100RB microcontroller, for blinking two LEDs connected…

A: 8051 Microcontroller is a programmable device which is used for controlling purpose.Basically 8051…

Q: For a combined datapath of add and addi instructions how many minimum multiplexers are required?…

A: To combine datapaths:          Select source of second ALU operand          Select source of data to…

Q: c) Identify the pin configurations of the following decoders. 3-to-8 line decoder (74138 IC) Pin # 9…

A: 1) The IC 74LS138 is a 3 to 8 line decoder, the main function of this IC is to decode and setup of…

Q: 28. For the 4-bit binary counter connected to the decoder in Figure 9–77, determine each of the…

A: The results of this can be that the Asynchronous counter suffers from what's referred to as…

Q: AM are made of flip

A:

Q: You are designing an IEEE single-precision floating-point multiplier targeting 200 MHz operation in…

A: Given :-  Floating-point multiplier = 200 MHz Cell library setup time = 200 ps (per second)…

Q: int i; for (i=0;i=2){ GPIOD_ODR &=~(1<<(i-2)); } } At each iteration what is LEDS that will be on…

A: According to the question, we have to explain that at each iteration which LED will be ON. In Step 2…

Q: Q): For the circuit in Figure. write a sequence of instruction to poll switch at 16 of 74F244 that…

A: Hello student I am giving this solution as per my best of knowledge  But I am sure that this…

Q: When the MPU performs am I/0o write bus operation DT/R = v. RD - and WR

A: Solution : DT/R*=1 RD*=1 WR*=0

Q: Draw a Write bus cycle where there will be at least 2 wait states and then explain the total diagram…

A: When processor is prepared to initiate the bus cycle, it applies a pulse to ALE during T1. Before…

Q: besign a 4-bit universal shift register to implement the followin

A: Q.

Q: Referring to the register transfer system below, determine the transfer operation, which will happen…

A: Answer

Q: sing instruction IN AL, DX to read a byte information from an input port, which register must be…

A: D.  AL register is used to receive tye 8-bits data.

Q: Design a two-bit binary counter with a single input x. When the input x=0, the counter stops…

A: Actually, flip-flop is a circuit.

Q: Provide a logic diagram of a 4x1 multiplexer but the decoder is expanded (meaning, show the logic…

A: According to the question we need to:

Q: 8086 circuit, assume that the connection of ports A and B is as follows. An information parallel to…

A: The 7 segment LED display is very common. It can display the digits from 0 to 9 along with a few…

Q: PICmicro A/D converter has been configure and the following register values are provided: ADCONO =…

A: The value in decimal read on ADRESH register is

Q: A. Design an interface circuit for three 8255 PPI's and minimum mode 8088 MPU. The memory-mapped…

A: The 8088 MPU may connect to a wide variety of peripherals using the 8255 PPI, a programmable…

Q: Given in the figure is IC 7474 pin configuration. The pin connections of the IC is provided in the…

A: Answer: Option b (AB): 10-&gt;11-&gt;10

Q: Given in the figure is IC 7474 pin configuration. The pin connections of the IC is provided in the…

A: Option C could be the answer 00----&gt;10----&gt;11----&gt;01----&gt;00 For D flip flop whenever…

Q: Explain how a tri-state output AND gate

A: NOTE: ACCORDING TO COMPANY POLICY WE CAN SOLVE ONLY 1 QUESTION. YOU CAN RESUBMIT THE QUESTION AGAIN…

Q: Design FFs only. a 3-bit synchronous counter using J-K

A: Synchronous Counter Synchronous counters are named as all flip-flops are clocked by the same signal…

Q: For a combined datapath of add and addi instructions how many minimum multiplexers are required?…

A: To combine datapaths:          Select source of second ALU operand         Select source of data to…

Q: sing the data book, label the pin configuration pr common anode, use 7448 IC and 7447 IC t Pin Nos.

A: A BCD to Seven Segment decoder is a combinational logic circuit that accepts a input of decimal…

Q: Problem 5 Write the entire VHDL code for a 64-bit synchronous counter that has a synchronous reset…

A: Write the entire VHDL code for a 64-bit synchronous counter that has a synchronous reset and an…

Q: 7. If the 8051 can operate using a 16 MHz crystal connected to its XTAL1 and XTAL2 inputs, and MOVX…

A: Let's go through each question one by one:7. Frequency of ALE signalIf MOVX instructions are not…

Q: How does the Cyclone III FPGA chip support efficient adder implementation?

A: Note : As per guidelines we are authorized to answer 1st question when multiple questions are…

Q: a PIC16F84A microcontroller where 2 inputs (to the microcontroller) are to be connected to pins RA0…

A: PIC16F84A is an 8 bit microcontroller which means that it is capable of processing 8-bits at a time.…