Q3: A three stage Cockroft-Walton generator is supplied by 212.133 V, 50 Hz source via a transformer with turns ratio equals to 2/800. All capacitors have a value of (0.8 uF). The protection current equals to 15 mA. Find the following: a. Find the output peak voltage that is used for testing without considering the voltage drop. b. Find the output peak voltage that is used for testing with considering the voltage drop. c. What is the ripple voltage? d. If the lowest capacitor is increased to twice its value, what is the output peak voltage that ioused for testing with considering the voltage drop. e. Comparing the results of ( b) and (d) above, do you recommend doubling the value of the lowest capacitor or not? According to the circuit values, is the 3 stages represents the optimum number of stages for this generator?

Q3: A three stage Cockroft-Walton generator is supplied by 212.133 V, 50 Hz source via a transformer with turns ratio equals to 2/800. All capacitors have a value of (0.8 uF). The protection current equals to 15 mA. Find the following: a. Find the output peak voltage that is used for testing without considering the voltage drop. b. Find the output peak voltage that is used for testing with considering the voltage drop. c. What is the ripple voltage? d. If the lowest capacitor is increased to twice its value, what is the output peak voltage that ioused for testing with considering the voltage drop. e. Comparing the results of ( b) and (d) above, do you recommend doubling the value of the lowest capacitor or not? According to the circuit values, is the 3 stages represents the optimum number of stages for this generator?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Needs Complete solution with 100 % accuracy.
Electrical Engineering How do I create a circuit that does the following. The output voltage Vout is at OV originally. If the input voltage Vin changes from OV to 1V, the Vout should also goes to 1V an will keep as 1V no matter how Vin changes later on. plz help draw the circuit diagram!
Q5
Please answer all subpart All subpart is compulsory for like Please
Please provide a clear solution. Please answer soon for I have 30 minutes left to answer. Thank you very much.
R148 R149 R150 If R148 is 18 Ohms, R149 is 13 Ohms, R150 is 25 Ohms, and there is 4 Amps flowing through R150, what is the current through R148? Please show 3 decimal places and don't include units in your answer (i.e. don't include A in your answer).
Needs Complete typed solution with 100 % accuracy.
The circuit is in continuity mode before the switch is opened. Select one: O a. 2. Select the option that corresponds to the circuit before opening the switch. R₁ O b. 3. O c. 1. E 3. E R₁ E L k E R₁ R₁ 2. R₂ R₂ R₂
Simplify the following block diagram 5 points into a single block. H3 R G1 G2 G3 H H1 1 Add file Simplify the following block diagram 5 points into a single block. R G2 G. H, Ha 1 Add file
For the following circuit, the load draws: TM4C Select one: O O 0 a. 3.3 A b. 3.3 mA C. 2.2 MA d. 8 mA e. 1 KQ f. 100 mA g. 3.3 V O h. 5 mA O 0 1ΚΩ Load
Attached below the figure and the question. * I need a step by step answer please :)
Give answer in 5 min i will give u like