Q3) A retaining wall of (6m) height at restcondition as shown in Figure (2). Calculatethe following:1.5mSandy SoilkNYt = 18.0-m²Ø = 30. 0°%3DWater Table Level (WT)Sandy SoilkNYt = 20.0-Ø = 30.0°3.0 mFigure No. 26.0 mw O'E

Answered: Image /qna-images/answer/c291e033-e7f1-46d7-bc41-dde7891e5a3c.jpg

Answered: Q3) A retaining wall of (6m) height at…

Engineering

Civil Engineering

Q3) A retaining wall of (6m) height at rest condition as shown in Figure (2). Calculate the following:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: If the retaining wall shown in Figure 1 is flexible, what will be the lateral force per unit length…

A: A retaining wall is given as Need to findLateral force per unit length

Q: Refer to Figure 12.10. Given: H = 7 m, γ = 18 kN/m3, Φ' = 25º, c' = 12 kN/m2, and α = 10º. Calculate…

A: The coefficient of active pressure is:…

Q: Using the picture as a guide, create a detailed estimate for a R.C.C. cantilever retaining wall that…

Q: Examine the rotational stability of the wall below 3 m 32 y=20 kN/m' $ = 36° For the right side: 6 =…

A: Given: A retaining wall as shown below Required: To examine rotational stability

Q: A reinforced earth retaining wall will have a height of 10.5 m. (35 ft) In this case: Calculate:…

A: Solution Given data height of 10.5 m. (35 ft)

Q: Figure shows a 4-m-high retaining wall, the wall is not restrained from yielding. Estimate depth…

A: Above given data we have to find depth of tension crack

Q: Consider the wall shown below. Dimensions are in meters. sand $' = 30 4 0.5 0.5 Determine the active…

Q: Determine the safety factor of a retaining wall (Concrete Density: 150 pcf, Soil Density: 120 pcf,…

Q: Draw a schematic or an FBD of the retaining structure. Indicate all the forces acting on it that…

A: 1 gravity force 2 active earth pressure force 3 friction force 4 normal force

Q: ▪ Determine the magnitude of the at-rest lateral earth force, Rankine active/pass unit length of the…

A: H=7m Y=17kN/m3

Q: In the retaining wall system given below, the wall height is 5 meters, the mH distance is 3 meters…

A: Consider the free body diagram ; Given; the wall height is , nH=5m the mH distance is =3m Force…

Q: In the retaining wall system given below, the wall height is 5 meters, the mH distance is 3 meters…

A: Assume that friction angle of soil retained by retaining wall ϕ=30°then coefficient of active…

Q: A reinforced concrete retaining wall is proportioned as shown below. There is a water table located…

A: Solution Data given: Bulk unit weight, γ = 16.93 Submerged unit weight, γsat = 9.67 Angle of…

Q: 12.6 Refer to Figure 12.10. For the retaining wall, H = 8 m, ' = 36°, a = 10°, y = 17 kN/m³, and c'…

A: Given retaining retaining wall, Height of the wall, H=8 m,Unit weight of soil, Cohesion of soil, c'…

Q: H = 8m x₁ = 0.40m x₂ = 0.60m Soil properties: Y₁ = 16.80kN/m³ Y2 = 17.60kN/m³ x₂ = 1.50m x₁ = 3.50m…

A: To find- The magnitude of pressure at the base of the heel.

Q: 3m R=1.2m R=1.2m Find the length of given figure above All dimensions Are c/c Wall thickness=0.4m…

Q: H = 8m x₁ = 0.40m x₂ = 0.60m Soil properties: Y₁ = 16.80kN/m² Y2 = 17.60kN/m³ x₂= 1.50m x₁ = 3.50m…

Q: 6.1m q = 16 kPa Y = 16.5 kN/m³ = 26° с = 10 kN/m²

Q: Assuming a smooth retaining wall as shown below. Calculate the resultant passive force from all…

A: ConclusionThe passive earth pressure coefficient (Kp) for the retaining wall with a wall friction…

Q: Page 3 of 4 q= 25 kPa p= 1500 kg/m 2 m c=0 = 22 1m is 2 m p= 2150 kg/m p= 2250 kg/m c= 25 kPa = 20 3…

Q: Refer to Figure 12.3a. Given: H = 12 ft, q = 0, γ = 108 lb/ft3, c' = 0, and Φ' = 30º. Determine the…

A: Solution; Calculate lateral earth force at rest using the formula; P0=qK0H+12K0γH2 Here, q is the…

Q: Figure below shows a retaining wall that is restrained f force per unit length for the following…

Q: 4) : For the retaining wall shown in Figure-3, determine the force per unit length of the wall for…

A: Given soil profile is, It is asked to determine the, 1. Force per unit length of the wall for…

Q: A transversal section of a long wall of uniform width is shown in the figure below. The wall is…

A: Question is based on the long wall of uniform width .Maximum load intensity , width of wall and…

Q: (20 marks) to below TI nkine active force, Pa, per unit length of here as H = 6 m , Hj = 4 m, y1 =…

Q: Given: wall shown in figure Required: maximum height of the wall (H) to gives Fs),iding 1.5 0.5 m C=…

A: Given data, F.S=1.5ϕ=30oγ=18 kN/m3C=0δ=25oγc=24 kN/m3Ca=20 kPa The factor of safety against…

Q: b. Lateral pressure due to soil (in kN/m2 per meter length of wall): @ point R = @ just above point…

Q: c) A retaining wall is shown in the figure below. Assume the backfill is in the active state and…

A: Given data in question Unit weight 18 kN/m3 Cohesion 5 kN/m2 Internal friction angle 30° Depth 5m…

Q: Variable X in this question is that last digit of your student ID. Enter X here: X = The embedment…

A: Embandment depth = 3.5 mKp = 3 KaYsat = 20 KN/m3Yw = 9.81 KN/m3x =8H = 6 + = 6 + 8/5 =7.6 mFINDForce…

Q: A vertical retaining wall 5.9 meters high retains a horizontal backfill having the following…

Q: If the passive resistance provided by the retained soil in front of the wall shown in figure below…

Q: Y-15 kN/m '-28° 4m G.WT. Yu 20 kN/m 4-33° c'0 4m The above figure shows a concrete gravity retaining…

Q: When excavating the stratum, calculating the support axial force for multiple times will produce…

A: When excavating the stratum, Calculation of the support axial force multiple times will produce…

Q: The design of a reinforced earth wall proceeds basically as follows: O Estimate the vertical and…

A: To fill the blank spaces.

Q: f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at…

A: Introduction- A wall is a framework and a surface that distinguishes an area, supports a load,…

Q: A vertical retaining wall 5.9 meters higl backfill having the following properties Gracvity = 2.67;…

Q: Problem (1) For the cantilever retaining wall shown in Figure, let the following data be given: H =…

A: Given, γ1=17 KN/m3φ1'=30c1'=0γ2=18 KN/m3φ2'=31c2'=40 KN/m2γconcrete=24 KN/m3k1=k2=23Pp=0

Q: Determine the total active force per unit acting on the retaining wall along with its point of…

Q: Compute the hydrostatic force acting on surface ABC exerted by water. Given wall width as 2 m.

A: Question is based on the surface ABC covered with water . Width of wall and depth from surface are…

Question

Q3) A retaining wall of (6m) height at rest
condition as shown in Figure (2). Calculate
the following:
1.5m
Sandy Soil
kN
Yt = 18.0-
m²
Ø = 30. 0°
%3D
Water Table Level (WT)
Sandy Soil
kN
Yt = 20.0-
Ø = 30.0°
3.0 m
Figure No. 2
6.0 m
w O'E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Lateral earth pressure distribution against retaining walls

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
25m Y=3m '0.4m find the Length of given Figure Albove Wall thick ness=0.4m SolVe by Centerline Method and Lonf wall-Short Wall Method.
Which of the two walls in Figure below gives the larger horizontal force? (Show calculations.)
c) A retaining wall is shown in the figure below. Assume the backfill is in the active state and determine the depth of the tensile cracks. Ze = 5m y = 18 kN/m³ c' = 5 kN/m² 4' = 30°
Hand written and clean writing please
A reinforced concrete retaining wall is proportioned as shown below. There is a water table located H1m beneath the ground surface. Use ultimate bearing capacity of 450 kPa. Based on the figure, the dimensions are given below. Use γc = 23.48 kN/m3 wall thickness = 0.47m footing thickness = 0.53m toe slab length = 2.33m heel slab length = 4.38m ground water table depth = 2.99 H2 = 3.84 The following values were calculated for this particular retaining wall: Righting moment: 3,868 kN-m/m Overturning moment: 908 kN-m/m Total vertical load: 999 kN/m What is the factor of safety for bearing pressure? Please answer this asap for upvote. Thanks in advance
Investigate the resistance of the wall, whose dimensions and floor properties are given in the figure, against overturning and sliding, based on the 1.5 safety factor. Note1: Evaluate as Pp-0. Note2: Take the kive k coefficients as 2/3. |g=150 kN/m² c=0, 0-30° Vosted 24 kN/m³ X=18 kN/m³ 6 1m 1m 0.5m 3m
Q5: In the case of the retaining wall depicted below. Calculate the lateral earth fore at rest per unit length of the wall. Determine the location of the resulting force as well as its magnitude. [25] y = 16.5 kN/m $ = 30 C = 0 Ground v Water table 2.5m Yur = 19.3 kN/m 0 = 30 C = 0 2.5m Good Luck
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
H.W 2: _Find the collapse load (Wu) for the isotropic slab shown below by using yield line theory. Assume m* =m= 25 kN.m 6 m 4 m 3 m 3 m
Q: For the retaining wall shown in the following figure, determine the force per unit length of the wall for Rankine's active state. Also find the location of the resultant. 3 m z 3 m y = 16 kN/m³ ' = 30° c' = 0 Groundwater table Y sat = 18 kN/m³ ' = 35° c' = 0
For the fixed wall thickness profile section in the figure; a) Find the center of shear (e). b) If a shear force of Ty = 40 kN is applied to the slip center Obtain the shear stress diagram that will occur. (t = 10 mm, a = 100 mm)