For the fixed wall thickness profile section in the figure; a) Find the center of shear (e). b) If a shear force of Ty = 40 kN is applied to the slip center Obtain the shear stress diagram that will occur. (t = 10 mm, a = 100 mm

Q: 5. The plastic block in Figure 4 is subjected to an axial compressive force of 600 N. Assuming that…

A:

Q: a) the shear strain yxy at point P. b) All stress components at point P.

A: modulus of elasticity(E) = 100 GPaPoisson's Ratio () = 0.3Reading of strain rosette ea…

Q: The principal stresses at a point in a bar are 160 N/mm² (tensile) and 80 N/mm² (compr.). The…

A:

Q: 4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of…

A:

Q: in. The pipe is subjected to a uniformly distributed torque of t = 63 lb-ft/ft along its entire…

A: Given:Uniformly distributed torque, t=63 lb-ft/ft…

Q: A hollow cylindrical shaft was designed to have a uniform wall thickness of 0.1 in. Defective…

A: Given:-The uniform wall thickness = 0.1 in The magnitude of the torque applied to the shaft = 17…

Q: Determine the average normal stress developed on the cross section as shown in Figure 1.

A: Average Normal Stress: When a force is applied to the structure which is perpendicular to the area…

Q: A hollow crank with an outside diameter of 4.8 in. and a wall thickness of 0.21 in. is subjected to…

A: The outer diameter = 4.8 inThe thickness of the crack = 0.21 inThe forces acting in the members are…

Q: For the structure below, assume that a = 60 in., b = 90 in., c = 40 in., and d = 50 in. Determine…

A: The given structure is analyzed by using the equation of equilibrium forces. The sum of all forces…

Q: Sketch the normal stress distribution acting over the cross section at section a-a. 6 kip 12 kip 3…

A:

Q: 3. (a) A prismatic bar is subjected to an axial compressive stress of 85N/mm. Determine the i.…

A:

Q: The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of…

A:

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: This question is related to the Strength of Material.

Q: At a point, the normal and shear stresses acting on one plane are 8,000 psf compression and 2,000…

A: Given: Compression of normal stress at point = 8000 psf Compression of shear stress at point = 2000…

Q: Determine the value of maximum shear stress Maximum principal stress-25.92 MPa Minimum principal…

A: Given data in question  Maximum and minimum principal stress To find out  Maximum shear stress

Q: 4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of…

A:

Q: 120 mm a 60° A torque T=30 kNm is applied to the hollow shaft shown that has a uniform 10- mm wall…

A: To find Shear stress at b?

Q: AL= 250 mm long circular rod with a diameter of D = 10 mm & made from A-36 steel is welded between…

A: Shear stress is the force that resisting force created by the object per unit area of cross-section,…

Q: ince P = 10 kN in the welded annex given in the figure, a) Write the equation for the neutral axis…

A: to find normal stress distribution

Q: PA 1.875 in. 0.75 in. 0.125 in. 1.25 in. r = 0.25 in. On the figure above, clearly mark with an "X"…

A: Stress Concentration - The max. stress accumulated or applied within a structural element is called…

Q: The flow of water, mass density = 1000 kg/m³ and kinematic viscosity v = 10-6 m²/sec in a commercial…

A:

Q: assume phi=0 throughout and tension crack filled with water, find FOS. the tension  crack is assumed…

A: Given- γ=1800Kg/m3C=39Kpaϕ=0

Q: Example: Determine the nominal eccentric compressive strength P, and the cccentricity e…

A:

Q: 2. The following square section is subjected to an unsymmetric bending moment M=850 Nm, as shown.…

A:

Q: *5-24. The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is…

A:

Q: H.W.I: For the section shown in Figure below, calculate: a. The balanced stoel reinforcement. b. The…

A: b (width of section) = 400mm D (total depth) = 710mm d(effective depth) = 640mm

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A:

Q: The copper pipe shown in the figure has an outside diameter of 3.000 in. and a wall thickness of…

A: Given; Uniformly distributed torque Outside diameter of shaft  Thickness of shaft To find: shear…

Q: Determine the block shear capacity of the following plate with holes shown. The holes are 0.026m in…

A: P=844.8NExplanation:for each hole,6P​=τs​∗4Π​∗d2∗2P=120∗4Π​∗0.0262∗12P= 764537.9882Nfor…

Q: The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of…

A: For the given copper pipe,

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: Determine the absolute maximum shear stress for each of the following plane stre states for which…

A: