Q3: A pitot-tube is inserted in a pipe of 300 mm diameter. The static pressure in pipe is 100 mm of mercury(vacuum). The stagnation pressure at the center of pipe recorded by the pitot-tube is 0.981 N/cm.Calculate the rate of flow of water through pipe, if the mean velocity of flow is 0.85 times the central velocity. Take C, 0.98

Q3: A pitot-tube is inserted in a pipe of 300 mm diameter. The static pressure in pipe is 100 mm of mercury(vacuum). The stagnation pressure at the center of pipe recorded by the pitot-tube is 0.981 N/cm.Calculate the rate of flow of water through pipe, if the mean velocity of flow is 0.85 times the central velocity. Take C, 0.98

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the pressure in the inlet? (Note: You cannot relate directly what is in the inlet section towards the exit/exhaust section, but: Inlet to Throat to Exit Section)
a2/ The flow velocity of water in a pipe is measured by a pitot static tube. The tube is placed at the centre of a 30 cm diameter pipe. The difference between the stagnation and static pressures measured as head of mercury and converted to head of water is 10 cm. If the coefficient of velocity Cv = 0.98. determine the velocity of water in the pipe. If the mean velocity is 0.7 times the centre line velocity, compute the discharge of water through the pipe.
The discharge velocity is 49 m/sec and 227 mm water gage. The suction pressure is 48 mm water vacuum and velocity of 3 m/s. Calculate the fan total head in terms of water. Answer in cm.
Q 2/ Calculate the difference between PRESSURE OF COMPRESSED AIR at point A and PRESSURE OF CONFINED WATER at point B located in pipes shown in Figure bellow. (PA- PB). Water B 3 m Water Air 1.5 m Air 1.2 m
Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
B9
A pitot tube is inserted into an air flow to measure the flow speed to measure flow speed. The Pitot tube is inserted into a 100mm diameter tube so that it points upstream into the flow and the pressure as show in figure 5 where p0 = stagnation point. The static pressure is measured at the same location in the flow, using a U-tube differential manometer. Consider density of air equal to 2.3kg/m3 and determine the air flow rate.
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 19 lb/ft^ 3 . What is the mass flow rate? If viscous effects are neglectedTake the specific weight for mercury equal to 846 and for water equal to 62.4 at 68 F
Problem 3
60 deg F engine oil flows in a 6" diameter pipe of length 13 feet. The gage pressure at the pipe inlet is 1 psi; the oil exits the pipe to the atmosphere. Determine the volume flow rate of the oil in ft3/sec. You can assume laminar flow.