Q3) a high level reservoir A supplies water through a pipe of 0.5m diameter 10 km long to a low level reservoir B. The difference in water level between the two reservoirs is 60 m.it is desired to supply water to the third reservoir C which is 100 m below the reservoir A, by a branch pipe taken from the main pipe 6 km from pipe entrance and run for further distance of 2 km. determine: (1) the diameter of the branch pipe in case that the discharge into each lower reservoir is the same.(2) Piezometric head at point D. (3) Draw the H.G.L.Take f = 0.032 for all pipes and neglect minor losses.

Q3) a high level reservoir A supplies water through a pipe of 0.5m diameter 10 km long to a low level reservoir B. The difference in water level between the two reservoirs is 60 m.it is desired to supply water to the third reservoir C which is 100 m below the reservoir A, by a branch pipe taken from the main pipe 6 km from pipe entrance and run for further distance of 2 km. determine: (1) the diameter of the branch pipe in case that the discharge into each lower reservoir is the same.(2) Piezometric head at point D. (3) Draw the H.G.L.Take f = 0.032 for all pipes and neglect minor losses.

Name: Q3) a high level reservoir A supplies water through a pipe of 0.5m di
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q3) a high level reservoir A supplies water through a pipe of 0.5m diameter 10 km longto a low level reservoir B. The difference in water level between the two reservoirs is60 m.it is desired to supply water to the third reservoir C which is 100 m b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Question 3 Water flows steadily through the variable area pipe as shown. a) Determine the velocities in the large diameter pipe (12 cm) and the small diameter pipe (8 cm). b) Determine the discharge. Open Open Oil S = 0.7 1.5 m 12 cm 2 m 8 cm-
В4. An orifice meter with orifice area 1039 mm2 is inserted in a pipe of area 2078 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 60 cm of mercury. Find the rate of flow of oil of sp. gr. 0.9 when the co-efficient of discharge of the orifice meter = 0.52. Head of water (in m) The discharge of water through pipe (in Litres/sec)
A horizontal pipe of diameter di at pressure P, carries water which has a constriction of diameter dz at pressure P2. Determine, a. Velocity of the water at di b. Velocity of the water at d2 c. The Flow rate
3.7 m 4 cm 3 diameter Group (D) 7.2 m Determine the discharge, the velocity of flow and pressure at the point (2)?
I need the answer as soon as possible
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Question 1 A pipeline of length 2000 m and diameter 200 mm connects two water supply reservoirs together. (a) If the value of the frictional factor, f, for the pipeline is 0.02 then determine the flow in the pipeline when the head difference between the two reservoirs is 20 m. (b) If an increase in demand requires that the flow be increased by 40% then determine what length of the same diameter pipe is required to satisfy this demand if it is connected as shown in Figure 1. Assume that the friction factor for the new pipe is the same as the existing one. New pipeline 20 m
None
As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is