Q3) A device has two sensors, one measuring the temperature and the second measure the current. The temperature sensor is a thermocouple gives output signal considered linearly proportional to the temperature between 0V and 20 mV for 0°C temperature and 150°C, respectively. Whereas, the current measuring sensor gives voltage proportional to the current between OV and 1V for 0A and 2A ,respectively. The temperature should not exceed 100°C and the current should be less than or equal to 1.2 A. The device should work only if the two mentioned conditions are both true. Design a circuit to make the device works according to those conditions, the device relay should get 5 V to switch it on, and OV make it off.

Q3) A device has two sensors, one measuring the temperature and the second measure the current. The temperature sensor is a thermocouple gives output signal considered linearly proportional to the temperature between 0V and 20 mV for 0°C temperature and 150°C, respectively. Whereas, the current measuring sensor gives voltage proportional to the current between OV and 1V for 0A and 2A ,respectively. The temperature should not exceed 100°C and the current should be less than or equal to 1.2 A. The device should work only if the two mentioned conditions are both true. Design a circuit to make the device works according to those conditions, the device relay should get 5 V to switch it on, and OV make it off.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Based on the given figure, a) what is the peak input voltage (V1)b) what is the peak output voltage, considering the diode drop of 0.7V?c) what is the average output voltage (Vave or Vdc), considering the diode drop of 0.7V?Round-off your final answer in 2 decimal places.
1
a) Determine the output voltage for all input voltages values. b) Sketch the overall output waveform, Vo(t).
The diode has a forward voltage of 0.7 V. V is a variable DC source, R1 = 11KQ and R2 = 6KQ. in R1 Vin R2 V out If V, is increased from zero, at what value of V, in volts will the diode start to conduct? in
Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C = 300µF placed in parallel with the load resistor RL = 1KN and Vm = 15V. Assume that the diodes are piece-wise linear with r,= 100 and V, 0.7V then derive the plot for the output voltage across the load resistor RL. Plot A V Plot C V wm Plot B V Plot D V please pick a plot
In a temperature measurement system the element A receives the temperature value and produces millivoltage as the output. This output is given to an element B. The element B increases the millivoltage value into voltage value. Then it is given to element C. The element C converts the analog voltage into Digital value .The element D displays the output. Identify the elements A, B, C and D used in the above mentioned temperature measurement system.
Question in the photo attached please
Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=0 for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms D3 D2 Figure 1
1. Connect the circuit shown in Figure (1), the power supply is set to zero volts. 2. Measure and record in table (1), the forward current in the diode at each level of voltage (Vf). 3. Determine the forward resistance Rf = Vf /If. A I KO E (0-4) V. Figure (1) Vr 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Ir R Table (1)
The resistors you can use in the shown below circuit have a maximum power dissipation level of 1W. If the diode has an absolute maximum rating of 1A, and can be modelled with a diode drop of 0.7 V. The maximum output voltage of the variable supply (VIN) is 14 V. What is the minimum value of resistance (R1) that can be used in this circuit? FT Vin R1 Vout
D₁ R₁ W D₂Z R3 R₂ Reverse Biased D1 lo Forward Biased V₂ D2 Reverse Forward Biased lo Biased 0.7V Assume R₁ = R₂ = R3 = 5k, V₁ = 5V, and V₂ = 15V for the above circuit. The diodes' IV characteristics are also shown above. Based on the IV characteristic plots, what are the cut-off voltages of D1 and D2? VD1, cutoff [V] VD2,cutoff [V]
I need the answer as soon as possible