Q3 50 kN 5 m 5 m. 3々 Analyze the above symmetrical otructure under the given symmetrical loading by using force mefhod

Q: Determine the maximum bending stress and shear stress on the same section.

A: Bending moment  at the section B=Mb =90×0.2-20×0.2×0.1=1.4 kN-m=1.4×106 N-mm Moment of inertia,(I)…

Q: SAMPLE PROBLEM NO. 1 AT-beam has the following properties: br 820 mm, bw 250 mm, d 470 mm, t 100 mm.…

A: Flange width(bf)=820 mm Web width(bw)=250 mm Effective width(d)=470 mm Thickness(t)=100 mm Concrete…

Q: 4. Four identical wires support a rigid bar as shown. If stress is not to exceed 150 N/mm², find the…

A: All the wires are identical so the diameter will be the same for all. The load at wire C is 40 kN.…

Q: 1. A rectangular reinforced concrete beam with width of 300mm and effective depth of 600mm is…

A:

Q: Shear Stress W= 1o EN/m 6. 5m T ? 2. Ta

A:

Q: Complex Frame

A:

Q: Q: - Analysis the beam shown below by the method of consistent deformation. El = constant A दे * 20…

A: A continuous beam fixed at C and roller supported at A and D. The beam is loaded with 20kN/m UDL…

Q: 11-95. The beam has the rectangular cross section shown. If w = 1 kN/m, determine the maximum…

A: Given: The value of w is 1 kN/m. Consider the figure,

Q: The cantilever beam shown in Fig. E4.8 has a rectangular cross-section 50 mm wide by h mm high. Find…

A:

Q: A cantiliver beam subjected to a uniform load along its length and axial load P. Draw the shear and…

A: Determine maximum shear force and maximum shear stress

Q: The steel bars AB and BC are pinned at each end and support the load of 300 kN, as shown. The…

A:

Q: A rectangular tubular column has the following properties: Nominal Width Along the X-Axis = 100 mm…

A:

Q: Draw the internal stress and strain diagram of beam considering that the depth of the stress block…

A:

Q: 8" H E = 36,000 ksi 5" Max Bending Stress: 1.25" TYP A simply supported beam has a symmetric cross…

A: Given Vmax = 800lb Mmax = 2400 ft-lb Required Maximum bending stress

Q: If M-50 kN-m, what is the maximum bending stress about the z-axis? (in O MPa)

A: To calculate the maximum bending stress for a given cross-section with given moment.   Given data,…

Q: the bending safety stress σem = 10 MPa, shear safety stress Tem = 600 kPa of the rectangular section…

A:

Q: The horizontal force P = 50 N is applied to the upper block with the system initially stationary.…

A:

Q: 1. A rectangular reinforced concrete beam with width of 300mm and effective depth of 600mm is…

A:

Q: A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 700 mm. It is…

A:

Q: 8 mm- 8 mm 250 mm 8 mm steel beam has the cross-sectional area shown. The beam is loaded as shown…

A: Given : w  = 70 kN/m Determine the absolute max. bending stress ?

Q: For a case of plane stress, o. = 40 MN/m², Oy = 0, Ty = 80 MN/m2. What are the principal xy %3D…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.