Q2/Calculate the impact resistance of a metal if it was chosen by the Charpy method, the cross-sectional area of the sample at the notch was 0.8 cm2, the pendulum weight of the hammer was 25.81 kg, the angle of elevation (a) was 141.5°, the length of the pendulum was 0.75 m, and the angle of turn back (B) was 12°?

Q2/Calculate the impact resistance of a metal if it was chosen by the Charpy method, the cross-sectional area of the sample at the notch was 0.8 cm2, the pendulum weight of the hammer was 25.81 kg, the angle of elevation (a) was 141.5°, the length of the pendulum was 0.75 m, and the angle of turn back (B) was 12°?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

15. Given the following data, plot the stress-strain curve for this tensile steel specimen. The gage length of the specimen is 2.0". The cross sectional area is 0.195 in². Use the diagram that you plot to determine: a.) The Modulus of Elasticity b.) The Yield Stress c.) The Ultimate Stress LOAD P (pounds) Deformation (inches) 0.0000 3000 0.0007 0.0017 0.0025 6000 9000 12000 14000 0.0036 0.0044 15000 0.0060 0.0100 16000 17000 0.0250 0.2000 0.4000 18000 12000* rupture occurred. 2.
A structural member 10 cm long must be able to support a load of 50,000 N without experiencing any plastic deformation. Given the following data for brass, steel, aluminum, and titanium, rank them from least to greatest weight in accordance with these criteria. Yield strength Ultimate tensile Alloy Density (g/cm3) (MPa) strength (MPa) Brass 415 600 8.5 Steel 860 800 7.9 Aluminum 310 435 2.7 * 700 Titanium 550 4.5
If the Vicker’s hardness number (HVN) is 350 N/mm2, how much load was applied on the test specimen to make an indentation of 2.15 mm?
Determine the parameters for each question below, assume E = 200 GPa. i) Critical load for the square column ii) Radius of the round column for which both columns have the same critical load iii) Express the cross-sectional area of the square column as a percentage of the cross-sectional area of the round column. |A 1'm Im 25 mm |D B
2-15 Brinell hardness tests were made on a random sample of 10 steel parts during process- ing. The results were Ha values of 230, 232(2), 234, 235(3), 236(2), and 239. Estimate the mean and standard deviation of the ultimate strength in kpsi. Ans: 50.111 kpsi Som- / -1 bpci
An ASTM A228 music wire has the diameter of 0.038 in Part A Find the ultimate tensile strength. Express your answer in pounds per square inch to three significant figures. Part B Find the ultimate shear strength. Express your answer in pounds per square inch to three significant figures.
You are a comparative evolutionary biologist that studies biomechanics. In particular, you are interested in how bone cross sectional shapes have evolved. You have discovered a rare (hypothetical) animal that has bone shapes similar to ours, but has solid, rectangular cross sectional areas. You conduct mechanical testing according to the parameters below and want to determine the: (A) moment of inertia; (B) reaction forces and moments at the fixed end O; (C) the stresses at points A, B, and C designated below, including the contributions of the different types of stresses at each point
Draw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking region
The 40mm diameter steel rod AB shown in Figure 2 is resting on frictionless rollers between two steel plates. End A is just touching the left hand steel plate. 2. Steel plate | A B Steel plate 1500mm Imm Figure 2 There is a gap of 1mm between the end B and the right hand side steel plate. The temperature of the rod increases by an amount AT and this increase in temperature causes the two ends of the rod to press against the steel plates. This action causes the right hand steel plate to move to the right by 0.5mm while the left hand plate does not move. The Young's modulus value for steel is 210,000N/mm?. Taking any assumptions that you deem necessary calculate the increase in temperature AT required to cause the rod to buckle.
Help me please
A piece of steel rebar is tested in tension to determine its mechanical properties. The length of the sample is 87.3 mm and the cross-sectional area is 52.1 mm². When stretched by 37.2 mm, the force measured is 14,884 N. At this point, the graph is non-linear, but no clear neck is visible. If the Poisson's ratio of the material is 0.281, calculate the cross-sectional area (mm²) at this point.
You are a comparative evolutionary biologist that studies biomechanics. In particular, you are interested in how bone cross sectional shapes have evolved. You have discovered a rare (hypothetical) animal that has bone shapes similar to ours, but has solid, rectangular cross sectional areas. You conduct mechanical testing according to the parameters below and want to determine the: (A) moment of inertia; (B) reaction forces and moments at the fixed end O; (C) the stresses at points A, B, and C designated below, including the contributions of the different types of stresses at each point