Q2.1 turbine runner has an exit velocity of 10 m/sec. The loss due to friction and other causes in the draft tube should not exceed 2.0 m. What maximum height of setting will you recommend for the turbine if the cavitation is to be avoided. The velocity of water at outlet of draft tube is 2 m/sec and cavitation commences when the pressure is 2.5m of water absolute.

Q2.1 turbine runner has an exit velocity of 10 m/sec. The loss due to friction and other causes in the draft tube should not exceed 2.0 m. What maximum height of setting will you recommend for the turbine if the cavitation is to be avoided. The velocity of water at outlet of draft tube is 2 m/sec and cavitation commences when the pressure is 2.5m of water absolute.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 lb/ft3. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for the mercury equal to 846 and for water equal to 62.4 at 68 0F.
Q2 Runner shaft. Figure shows a Kaplan turbine. The flow of Ha water rotates the runner at 200 rpm to generate power. The 28.575 mm diameter runner shaft is to be supported by the Water in Water in bearings at "a" and "b". The runner mass is 80 kg and an 800 N downward axial force is exerted by the water flow at the CG point of each blade. There are 4 blades. Runner a) Choose appropriate tapered roller bearing at b. b) Choose suitable ball bearing at a. c) What will be the combined reliably of both bearings? Consider: Bearing life = 30kh, Application factor = 1, Reliability goal = 92%
I need the answer as soon as possible
Cou
The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40
Water 2. In this system, d = 6 in., D = 6 ft, and =z2 = 12 ft. The water in the system is 13 cfs. machine a pump or a turbine? pressures at points A and B? losses. Pump 1. The discharge in the siphon is 2.80 cfs, D = 10 in., L1 = 3 ft, and L2 = 3 ft. Determine the head loss between the reservoir surface and point C. Determine the pressure at point B if three-quarters of the head loss (as found above) occurs between the reservoir surface and point B. 1 m REVIEW Home Work (1) Energy Equation Water T = 10ºC REPPER Water Same elevation Machine Elevation = 40 m -Elevation = 20 m Elevation 10 m 300 m + -300 m- 4. Assume that the head loss in the pipe is given by hL = 0.014(L/D)(V2/2g), where L is the length of pipe and AZ₂ AFL B Elevation 100 m L = 100 m D = 60 cm Water T= 10°C 3. A water discharge of 10 m3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7V2/2g (V is velocity in the pipe), how much power will have to be supplied to the flow…
= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
A pump is delivering 160 liters per second of water using an impeller diameter of 254mm and operating at a speed of 1800 rpm. If the speed is held constant and the impeller diameter is changed to 203.2 mm, what is the new discharged of the pump in liters per second?(128 L/s)
Water flows at the rate of 5 ft/s through an inclined pipe. At point A, where the diameter is 12 inches, the pressure is 15 psi. At point B, the diameter is 6 inches and the center of the pipe is 2 feet lower than at point A. a. Draw a clear diagram of the pipe system that indicates the following: (a-1) water flow reflecting the quantities involved in describing fluid flow and (a-2) the object of interest and the quantities that describe Bernoulli's equation. b. Write the Bernoulli's Equation using subscripts U ad L for the upper and lower points respectively and determine the pressure at point B?
6.7. Calculate the force exerted by the water on this orifice plate. Assume that water in the jet between orifice plate and vena contracta weighs 4.0 lb. 0.75 0.20 10' d
1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is 300 litres/s and the head lost due to friction is 5 m. Take the value of C = 50 in Chezy’s formula.
The answer is one of the options below please solve carefully and circle the correct option Please write clear .