Q2. Two discs of 20 cm diameter are placed I mm apart and the gap is filled with an oil of viscosity 0.8 Kg/m.s. Determine the power required to rotate the upper disc at 600 rpm while holding the lower one stationary.

Q2. Two discs of 20 cm diameter are placed I mm apart and the gap is filled with an oil of viscosity 0.8 Kg/m.s. Determine the power required to rotate the upper disc at 600 rpm while holding the lower one stationary.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the energy added by the pump. 160mm w EL. 200m 200mm 9 El.150m Oif. Sp.gr.=(0.82
A piston/cylinder receives R1343 at 300 Pa and compresses it in a reversible adiabatic process to 1000 kPa. 60-C. Find the tempature and sketch the p-v and T-s diagrams
i need the answer quickly
B A shaft turns at 150 rpm under a torque of 1500 Nm. Power transmitted is (a) 15 kW (b) 10R kW (c) 7.5 kW (d) 5 kW
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 cm diameter. A lubricating oil which fills the space between them has Viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. 1 14 cm VF- 0.86 Kgt
A drum with a 500-mm radius is attached to a disk with a radius of 250 mm. The disk and drum have a combined mass of 15 kg and a combined radius of gyration of 400 mm. A 12 kg block D is suspended by a wire that is warped around the drum. Another force P- 100 Nis applied to the wire that is warped around the disk. If the system is released from rest, neglecting the effect of axle friction determine: (a) the acceleration of the block. (b) the velocity of the block after 10 second. (c) the distance travelled by the block after 10 second. (d) the revolution by the drum just after 10 second. 500 mm P+ 250 mm
2. The 50 kg uniform crate initially rests on the inclined surface. If a force (F-40t +200 N) as shown in the figure below starts to pull the crate, determine the power output develop by the force at t-6 s. The coefficients of static and kinetic friction between the crate and the surface are s-0.20 and Hk-0.15. F-40t+200 N F (r in second) 30°
Question Certain fluid parameters are provided The inner cylinder, with a diameter of 20 cm, remains stationary, while the outer cylinder, with a diameter of 21 cm, holds the liquid up to a height of 30 cm. There is a 1.0 cm gap between the bottom of the two cylinders. By rotating the outer cylinder at a speed of 200 revolutions per minute (r.p.m.), the torsion meter attached to the inner cylinder registers a torque of 6.0 N-m. a. Determine the toque on the bottom in terms of b. Determine the toque on the surface in terms of ..... c. Determine method the viscosity of a liquid (N-sec/m^2)(Ans up to 2 decimal) μ (Ans up to 4 decimal) ..u.(Ans up to 4 decimal) using the rotating cylinder
Determine the resultant force of the water acting on the circular glass plate that Is to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top. Question 2: FYw.h.A ate Fv= Yw.V 3 m radie 9810 Ixr x gate 9810 1 m 2 m Ma:0 Nar3- Fn 号×3-fvx3- -0 Ma=0-) NBx3- F t /2Fy-0 120° 3 m 1,- I,
Q3) In impact of jet experiment if the supplied discharge Q through a 5 mm diameter nozzle is (0.25 L/s), find the required weight W that is needed to support the plate in its initial position as shown in figure. 50 mm W Nozzle