Q2. Find the velocity and acceleration of the piston and the angular velocity and angular acceleration of link AB for the crank slider mechanism shown in figure 2. The crank OA rotates anti-clockwise at 500 rad/min with constant velocity. Point O is fixed. A 200 mm 100 mm 600 45° Figure 2

Q: How many degrees are required if we taper a copper if it is measured .45 ft. as its taper per foot?…

A: Taper length, L= 0.45 ft= 0.45(12)= 5.4 in Larger end diameter, D1= 7.2 in Smaller end diameter, D2=…

Q: 6 - From the question (5) find the real length of the line AB. *

A: the real length of line AB

Q: For the beam cross section shown, bending is about the z axis. All dimensions are in inches and,…

A:

Q: thread the outer Jiem 10

A: Given data Outer diameter =26mm Inner diameter =18mm

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A: Given Shaded area To find Centroid

Q: If the ratio of the velocity of outward stroke and velocity of return stroke is 8, then the Koitie…

A:

Q: Q- 6- Resolve the force 250N into rectangular components 250 N 16 9. 12

A: Here, Magnitude of the force = 250 N   For the given triangle, missing angle θ can be found by,…

Q: w the components of F along the u and v w the triangle with sides and angles labeled to be able to…

A:

Q: It is known that the connecting rod AB exerts on the crank BC a 2.5-kN force directed down and to…

A: The free-body diagram of the given system is shown below.

Q: 6. FA and FB balances the metal beam with a 360N of weight. FB experiences a force of 200N while Fa…

A: According to the given information, we have two reaction forces FA and  FB  where the weight on the…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: A belt drive consists of pulleys of one pulley of diameter 667 mm and another pulley of diameter 321…

A: Given data,  D=667 mm  d= 321 mm  Cross belt arrangement  Center distance arrangement x= 2.6 m…

Q: The assembly above is constructed out of a bent circular rod with a diameter of 1 in, Which of the…

A:

Q: 2. Determine the moment of the four forces acting on the rod as in the fig. about point 'o' 40 N N…

A: The free body diagram for the body is given below,

Q: Bar AB rotates as shown with an angular velocity equal to 1O rad/s. Assume AB ha a length of 500mm…

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: a=75 mm b=160 mm c=20 mm determine the moment of interia Y prime

A: Given Data

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Determine the horizontal and vertical stroke of a slider D and F when crank AB rotates 30 legrees…

A:

Q: Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A: In this question, force 500lb is to be resolved along two mutually perpendicular lines, one is…

Q: Find the mass of a cube of edge a, if the density varies as the sum of the distances from three…

A: Consider a cube of edge a, now it is given that, ρ=k(x+y+z)                 where, k is the…

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: 4 in 2 in 4 in 8 in -12 in 16 in-

A: Given data To determine the moment of inertia and radius of gyration about x and y axis

Q: Determine the normal force at point C(Nc) Express your answer in kilopounds to three significant…

A:

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Q: 15ob Q3: Find the resultant and its orientation.

A: from fig. it is clear thatForce FA starts from A to CGiven :- FA=180lb FB =150lb

Q: Q/Find the value of T (kN. m/m) So that the value of angle of twist at D equal to zero.

A: The elemental angle of twist for the shaft CD can be expressed as, On integrating the above…

Q: Does this machine maximize or minimize the force (100 lb)* 100ib 20m. 45 15 in. 05in. 100lb

A: Given: Plier with dimensions and forces To find: The effect on force requirement

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: •2-33. If F, = 600 N and = 30°, determine the magnitude of the resultant force acting on the eyebolt…

A:

Q: Solution of how to find the inclination and direction of resultant force

A:

Q: f B=650 N Solve for: •Line of action of the Resultant Force •Horizontal and Vertical Force on each…

A:

Q: Find Ix for the shape below:

A: To determine: The moment of inertia of the shape about X axis. Image: Consider a image below:

Q: Determine ỹ, which locates the centroidal axis z for the cross-sectional area of the I-beam, and…

A: Moment of inertia of an area is defined as the product of area and the distances of its center from…

Q: FA and FB balances the metal beam with a 360N of weight. FB experiences a force of 200N while FA is…

A: Given Data⇒ Weight of beam(W)=360 N FB=200 N θ=30° Required Data⇒ Using SINE/COSINE LAW, solve fora)…