Q2. A 50kVA, 6360/240V, 60Hz, A/A-connected three-phase transformer has the following test data: Open circuit test: Voc = 240 V, Short circuit test: Vsc 157.74 V, Ioc = 7.862 A, Isc = 120.3 A, Poc = 2 kW Psc = 2.835 kW Calculate in primary terms (refer to HVS): I- The approximate equivalent circuit parameters referred to H.V.S. draw the circuit. II- The voltage regulation when supplying 34 of its full-load at 0.8 leading power factor. III- At what load the maximum expected efficiency occurs if the power factor is 0.8 leading.

Q2. A 50kVA, 6360/240V, 60Hz, A/A-connected three-phase transformer has the following test data: Open circuit test: Voc = 240 V, Short circuit test: Vsc 157.74 V, Ioc = 7.862 A, Isc = 120.3 A, Poc = 2 kW Psc = 2.835 kW Calculate in primary terms (refer to HVS): I- The approximate equivalent circuit parameters referred to H.V.S. draw the circuit. II- The voltage regulation when supplying 34 of its full-load at 0.8 leading power factor. III- At what load the maximum expected efficiency occurs if the power factor is 0.8 leading.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given three phase fullwave with center tapped transformer with 220 Vac source voltage, determine: Vdc, Vrms, Pdc, RF, and efficiency. D1 L1 D2 L1 L7 D3 220 Vac, 60 Hz Vo D4 RL=10 ohms L2 D5 L3 D6 m. L6 3 F12 87
Please solve this
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs-0.008Ω RHs-2.6Ω R-Hs-5000Ω X.s-0.015Ω XHs=5.22 Xm,HS=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side.
conductor radius is 0.75cm
1. Convert the following decimal numerals to their binary, octal and hexadecimal equivalents (in case of infinite extension, compute the first 10 digits after dot): a. 55438, b. 237170, c. 586.609375 d. 22.016845703125 e. 416.712 2. Convert (416.715); to its decimal, binary, and hexadecimal equivalent 3. Find appropriate numeral system base, for which given equation is correct: a. 12,1 = 302/20 b. 41/3 = 13 c. 23+44+14+32 = 223 4. Find 8-bit l's complement numerals representing the following decimal numerals: a. 89 b. 135 c. 225 d. -37 e. -78 f. -128 g. -230 5. Repeat task 4, this time searching for 2's complement numerals 6. Compute: a. 11100 + 10001 b. 11100 + 00100 c. 01100 - 10011 assuming (one-by-one): signed-magnitude, l's complement, 2's complement representation
don't copy
A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3-phase side. The main transformer primary to secondary turns ratio is (12/1).
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs=0.0082 RHs=2.62 Rfe-HS=50002 XLs=0.015N XHs=5.2N Xm.Hs=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM