I need the answer at 20 minute . Q1: Design an FIR linear phase, digital filter approximating the ideal frequencyresponse:Q2: Repeat Q1 for a band-stop filter having the ideal response:48Ha(w) = 0,1, = |ol < TT-6-3Without use matlabV VI|w|≤3 3 3VI VT-6-3

Given: Frequency response of a digital filter, Hdω=1;ω≤π60;π6<ω≤π31;π3≤ω≤π, To find: Coefficient…

Answered: Q2: Repeat Q1 for a band-stop filter…

Engineering

Electrical Engineering

Q2: Repeat Q1 for a band-stop filter having the ideal response: TT 1, |w|≤ = 0, Ha(w)= = 1, 7673 <|w| < -6-3 π 3≤|w|≤π

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a series RLC bandpass filter as shown in the figure with lower cut-off frequency f = 400 Hz and bandwidth B = 9600 Hz %3D a) Determine the higher cut-off frequency f# b) Determine the center or resonant frequency fo in Hz and wo in rad/s and calculate the quality factor Q c) Choose C = 2 nF and find the values of R and L to meet the design specifications C No V: O
I want the answer in detail and as quickly as possible please Q/ Using capacitors and resistors, design A - (band-pass filters) with Fl=108HZ and Fh=112HZ. B - Design (band-pass filters) with Fl = 218HZ and Fh = 223HZ. %3D ((And make sure that the values are available in the market))
Design an active band pass filter with Gain= -20 and cutoff frequencies at 100 Hz and 10 kHz using the following circuits. (Must show your math, including the formula used in your calculations) Gain = -R2/R1, Gain (dB) = 20log(|Gain|) Determine R1= C1= R2= C2= Draw the simulated frequency response of the circuit dB Gain vs f (three straight lines) on the graph paper. 20 - C2 HH 0- R2 R1 C1 -20 - Av Vin Vout 40 - -60 - R fe = R, fc, = 2rR,C2 Voltage Gain = 2rR,C 10 10 Hz 10° 10 10 10" (gp) ujeg
Draw the circuit of a low pass RL filter and find the transfer function. Cutwith a frequency of 70 HzDesign a low pass RL filter. The amplitude-frequency-curve of this filter you designed.Draw in accordance with the calculated values.
2. The circuit of the Figure is a notch filter. Generate a magnitude plot of the transfer function H(f) = Vout/Vin with frequency ranging from 10 Hz. to 100 kHz. Then, analyze the circuit at very high and very low frequencies to provide checks on the plot. Use the plot to determine the frequency of maximum attenuation and the value of the transfer function at that frequency. Hint: Use the phasor transformation. www R₁ R₁ = 90 92 R₂=1022 R₂-100 £2 0000 L ww R₂ L = 100 mH C=0.1 μF www Ry Vout
I need some help. I am designing a bandpass filter with fl=3400 Hz and fh= 7500 Hz. Based on that I need the values for the RCL circuit, assuming that the capacitor is 1 microfarat. So, I need some help in calculate the center frequency, bandwith, Q, center frequency as well. I need clear steps and calculations. Any help will be appretiated.
The following figure shows a system that couples an inverting band pass filter with a high pass filter. Using parameters given in the figure, derive the transfer function of Vo(s)/Vi(s) Vi Inverting band pass filter R₁ ww C₁ C₂ R₂ High pass filter C3 R3 R4 R5 Vo Hint: You could start with writing the transfer function of the two filters separately, then combine the two equations into one. Your transfer function may be written as the product of multiple filters and/or gain stages - you do not need to reduce to simplest form but you should have each piece derived somewhere.
4. A simple band-pass filter can be designed by cascading one-pole high-pass and one-pole low-pass filters. Using op- amp circuits similar to the one shown below, design band-pass filter with cutoff frequencies of 200Hz and 50 kHz and with a midband gain of 10dB. Resistor values must be no larger than 200k, but the input resistance must be as large as possible. Vic C oV₂ V₁ www OV
Design a series RLC bandpass filter as shown in the figure with lower cut-off frequency f = 400 Hz and bandwidth B = 9600 Hz a) Determine the higher cut-off frequency fH b) Determine the center or resonant frequency fo in Hz and wo in rad/s and calculate the quality factor Q c) Choose C = 2 nF and find the values of R and L to meet the design specifications C R No
3. Active Analog Filter Topologies You already know from our class discussions that Circuit 1 is an active analog Low-Pass Filter For each of the remaining three circuits, state whether the circuit will function as a low-pass or high-pass filter. Each of your answers must be accompanied by a brief explanation and justification incorporating the frequency dependent characteristics of the reactive circuit elements. That is you should look at the asymptotic impedance of the L and C if the input signal the frequency is very low or very high. Sketch the expected Bode plot for 20 log(Vo/Vs) as a function of log (f) labeling the corner frequencies. No equations are required! R2 R2 R2 R2 R1 R1 R1 Vs Vs o W- Vs Vs Vo Vo Vo Vo Circuit 1 Citcuit 2 Circuit 3 Circuit 4
Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.
Answer the following wuth illustration and solutions. 1.) A second-order band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 500Hz and below 1.5kHz. Assuming that both the resistor have values of 1kohms, calculate the values of the two capacitors required. Find also the center frequency of the two frequencies. This is the example/guide that might help.