Q2\ It is required to use a diodes specified to have a 0.9V drop at a current of 1 mA. The diodes are to be included in a voltage regulator to keep voltage level at 1.07v to load resistance 1.9k2 as in the circuit shown in the figure. (a) Determine the value for the resistance R and the current passes through the diodes when connecting the load resistance. (b) When removing the load resistance, find how will the output voltage changes with its value? (c) Estimate the change due to change the load resistance with 750 2? (Assume the diode are small-signal diode modeled to calculate all changes in output voltage)

Q2\ It is required to use a diodes specified to have a 0.9V drop at a current of 1 mA. The diodes are to be included in a voltage regulator to keep voltage level at 1.07v to load resistance 1.9k2 as in the circuit shown in the figure. (a) Determine the value for the resistance R and the current passes through the diodes when connecting the load resistance. (b) When removing the load resistance, find how will the output voltage changes with its value? (c) Estimate the change due to change the load resistance with 750 2? (Assume the diode are small-signal diode modeled to calculate all changes in output voltage)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
A full-wave bridge rectifier with a 100V rms sinusoidal input has a load resistor of 1 k. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. D.
1 Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage Ve-20 V and bias voltage VBi= 2.7 v. PP a) What is the function of the circuit . b) Draw the circuit diagram.
In this Zener diode regulator, the source voltage varies from 7 V to 12 V. Assume that the load current varies between 2 mA and 31 mA, and that the diode is an ideal 3 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures.
For the portion of the diode curve does the zener diode look like an open circuit: (a) Diode voltage less than the zener voltage. (b) Diode voltage greater than the zener voltage. ( )
The contact potential difference of a metal-n type semiconductor Schottky diode is 0.6 Volts. For V = 0 (balance), V = 0.2 Volt (Straight supply), V = 2 Volt (Reverse supply) respectively: a) Calculate the width of the joint area. b) Draw the energy band diagram of the diode for each case. (Show the values you have given and found on the drawing.) (For the semiconductor, donor concentration is 1016 cm-3 and dielectric permeability 1.1x10-10 F/ m take.)
In this Zener diode regulator, the source voltage varies from 6 V to 10 V. Assume that the load current varies between 2 mA and 33 mA, and that the diode is an ideal 3 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
In each of the ideal-diode circuits show below V1 is a 1kHz, 10-V peak sine wave. Sketch the wave form resulting at V0. What are its positive and negative peak values?
The four diodes used in a bridge rectifier circuit have forward resistances which may be considered constant at 1 ohm and infinite reverse resistance. The alternating supply voltage is 220 V r.m.s. and load resistance is 580 ohm. Calculate (i) mean load current and (ii) power dissipated in each diode.
Diode circuit...do it...
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.