Q2: For this horizontal T through which water (p =1000 ) is flowing, the following data are given:kgm3m3Q2 = 0.10"3Q1 = 0.25-SS100 kPa, p270 kPa,15 ст,P1 =P3 = 80 kPa, D,D2 = 7 cm, and D3For these conditions, what external force in the x-yplane (through the bolts or other supportingdevices) is needed to hold the T in place?3 15 ст.y1)3Q3D1D3H(2D2

Answered: Image /qna-images/answer/08b0b671-61c7-46ec-b158-e3ab12451da5.jpg

Q2: For this horizontal T through which water (p = 1000 ) is flowing, the following data are given: kg m3 m3 Q2 = 0.10" Q1 = 0.25 %3D S S P1 = 100 kРа, р2 70 kPa, P3 = 80 kPa, D1 = 15 cm, D2 = 7 cm, and D3 For these conditions, what external force in the x-y plane (through the bolts or other supporting devices) is needed to hold the T in place? 3 15 ст. y 1) 3 03 D1 D3 Q2

Q2: For this horizontal T through which water (p = 1000 ) is flowing, the following data are given: kg m3 m3 Q2 = 0.10" Q1 = 0.25 %3D S S P1 = 100 kРа, р2 70 kPa, P3 = 80 kPa, D1 = 15 cm, D2 = 7 cm, and D3 For these conditions, what external force in the x-y plane (through the bolts or other supporting devices) is needed to hold the T in place? 3 15 ст. y 1) 3 03 D1 D3 Q2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

NSCP 2015 PLEASE CLEAR HANDWRITING
Please answe the problem attached image, thank you very much using NSCP 2015,Asap
Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in Ø bolts at the usual gage locations. The stagger is 1 1/2 in. (Ans. 2.98 in^2)
Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi f) what is the block shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)
A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
Please help with the problem below
B2
2. A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1 will be the top and bottom flange members while the Plank 2 will be the web member. A sample l-beam is shown below. In addition to that, a steel plate will be installed (at the center) at the bottom of the l-beam to ensure its strength. Calculate the I subscript x with bar on top end subscript (Moment of Inertia with respect to centroidal x-axis) of the built section. b top flange h bot flange 1 1 3b b 3b 8 4 8 tp Wp Given o b = 2.1 cm h = 36 cm tp = 0.55 cm wp = 21 cm 2. web
19. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksis) what is the block shear rupture capacity of beam flange of the flange connection in kips? (2 decimal places)
SITUATION III. For Items 13-14. Refer to figure 7. 60 kips The cast iron block with cross-sectional dimensions of 2.5 in. 2.5 in. by 2.5 in. consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 2.5 in. long. If the working stresses are 40 ksi for cast iron in bearing and 50 ksi for the key in shear, determine the following: Key 55° 13. The safe smallest dimension of b. a. 0.39 in b. 0.53 in c. 0.75 in FIGURE 7 d. 0.98 in е. none of the above