i need the answer quickly Q1) For common collector circuit, exactly find-1. VCC value that lead to best Q-point?2. The voltage gain with draw A.C equivalent circuit at (re' 102)?3. The Rin (total) at (re' 10n)?4. The current gain at (re' 102 and AV = 0.8)?Q2) For common base circuit, at (VC : 10.4v) exactly find-1. VCC value?2. VCB value?solve Q2 only3. The R1 value approximately at VCC = 20?4. The power gain approximately?Q3) For common emitter circuit, (Answer four only but with 2 and 6)let (Cwi = 5p, Cwo = Cce 8p, Cbe 40p, Cbc-12p, Cl C2 0.01 p)exactly find:-1. The Q-point?2. At (re' = 205N), the voltage gain with explain?3. The Vo p.p.(max) at (re' 200)?4. The Rin(total) and Rout approximately at (AV = - 24 and re' 202)?5. the low critical frequencies at (AV = - 24, Zin = 20k and Zout 5K)?6. the high critical frequencies at (AV = - 24, Zin = 20k and Zout = 5K)?12v5.6kVCCOVCC Q2.8k250kR13s RB1 250kC210020Hw199 c2ci"188k H100RB2C1三20028.2k21.2k:2k

Given: In the above given question they have mentioned a common base configuration which is made up…

Answered: Q2) For common base circuit, at (VC =…

Q2) For common base circuit, at (VC = 10.4v) exactly find - 1. VCC value? 2. VCB valuc? 3. The R1 value approximately at VCC 20? 4. The power gain approximately? solve Q2 only

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
I need the answer as soon as possible
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
i need the answer quickly