Q2 / For a current of r. m. s value 5 A, and frequency 2 kHz, write down the standard expression. Hence, calculate (a) the instantaneous value 150 micro second after it passes through zero, and (b) the time taken for it to reach 4 A after passing * .through zero for the first time

Q2 / For a current of r. m. s value 5 A, and frequency 2 kHz, write down the standard expression. Hence, calculate (a) the instantaneous value 150 micro second after it passes through zero, and (b) the time taken for it to reach 4 A after passing * .through zero for the first time

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ql: A fission reaction is shown in figure, A uranium nucleus is excited by the neutron , and it split into two nuclei (krypton and barium) and emit three neutrons. barium 3 neutrons uranium neutron energ krypton before and after the reaction the difference in mass of particles is: 235.0439231 - 91.9261528 - 140.9144064 – (2*1.0086649) = 0.186034 amu How much energy (in KWh) is released per nuclear fission reaction?
Draw band diagrams for below contacts. a) metal-n-type semiconductor for Φm< Φs b) metal-n-type semiconductor for Φm> Φs c) metal-p-type semiconductor for Φm< Φs d) metal-p-type semiconductor for Φm> Φs Clearly specify type of contact, Schottky barrier, built-in-potential and the depletion width in the band diagram
a) A single-phase uncontrolled bridge rectifier supplies a highly inductive load from a single- phase 50 Hz AC voltage source. By neglecting the effect of line inductance, the rectifier generates average output voltage and current values of 180 V and 6 A, respectively. Due to the highly inductive load, the current waveform is constant and ripple-free. However, when considering a line inductor of 5 mH, the average output current drops by 3%. i) With an aid of a circuit diagram, explain the reason behind the zero voltage across the rectifier's output during the commutation interval. ii) Calculate the commutation angle and the average voltage drop values.
Question 2.a An ac power supply with VRMS =240 V and a full-wave rectifier are used to generate a de voltage for a resistive load with resistance value of 100 Q. The filter capacitor connected to the rectifier has capacitance value of 500 µF. The frequency of the ac supply is 50-Hz. Determine the de voltage and ripple factor at load side? а. Question 2.b Assume that by using an RC filter circuit, you wanted to reduce the ripple factor to half the amount that you calculated in part 2.a, answer the following questions: b. What values would you suggest for resistor and capacitor of the RC circuit? What is the voltage regulation of this circuit? с.
In a 36KV overhead line, there are 3 units in the string of insulators. If the capacitance between each insulator to pin and earth is 55% of self-capacitance of each insulator. Find the distribution of voltage over three insulators and string efficiency.
a) Explain why root mean square (RMS) is used to quantify the strength of an AC signal. b) If SI units are Meter (m), Kilogram (kg), Second (s), Ampere (A), Kelvin (K), Mole (M) and Candela (C), then express Voltage, Resistance, Capacitance, Inductance, Power and Energy in terms of SI units.
hi, can you help me with this whole question. thank you
In the Chapman-Enksog predictive model of conductivity of gases, increasing the temperature from 300 K to 400 K will increase the conductivity by the 2k to be independent of temperature. Why? A) 15.4 B) 33.3 C) 86.6 %. Assume that
a) N B) NC NS) N/C D) nm TO) n/m
Define the continuity equation, then discuss the relaxation time in dielectric and conducting materials.
If the input voltage for the given circuit below is 220 V at 60 Hz, the load resistance (RL) is 3302 and the average output voltage is 20 V. Assume the diodes to be silicon diodes. Determine the turns ratio of the transformer used. If a capacitor of 100 µF is connected parallel to the load resistor (RL), Determine the ripple factor. D3 D1 V + RL D2 D4 a. The turns ratio of transformer (Npri/Nsec) is b. The Ripple factor is illl