Q2 (a) Two single-phase voltage sources, Vị and V2 are connected by parallel line impedance of Z11 = 1+ j2 n and Z12 = 3+ jN as shown in Figure Q2(a). If, V, = 230210° V,ms and V2 = 240220° Vms (iv) Draw the power triangle of source, V2. (v) Determine the real power loss in the line. ZLI Z12 V1 V2

Q2 (a) Two single-phase voltage sources, Vị and V2 are connected by parallel line impedance of Z11 = 1+ j2 n and Z12 = 3+ jN as shown in Figure Q2(a). If, V, = 230210° V,ms and V2 = 240220° Vms (iv) Draw the power triangle of source, V2. (v) Determine the real power loss in the line. ZLI Z12 V1 V2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Subject - Design electrical circuits for single-phase AC networks Question - Compare the effect of varying resistance, capacitance and inductance in parallel and series AC circuits on voltage, resistance and impedance
Each line of a 3-phase system given in figure is suspended by a string of 5 identical disks and the ratio of C1/C=0.1 (Shunt capacitance per self-capacitance) is given. If the string is connected to line of voltage 33kV. a) What is the voltage distribution over the unit of string and what is the string efficiency? b) When the string is supplied by a Guard Ring and this lead to add a two air capacitance of value 0.2C, 0.1C respectively to the nearest to the conductor. Find the new voltage distribution and the new efficiency.
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
1 PROBLEM 20020° V rms, Vbn 1. A balanced three-phase Y-Y system has the phase voltages of Van 200/120° V rms, and Ven = 2002(-120°) Vrms. The load impedance per phase is Z₁ = 50 - j100 n. a Van Vcn n Vbn Ia Ib Ic B Zu (b) Determine the line currents Īa, Ip and Īc. (c) Determine the total average power delivered to the three loads. N C = ZL (a) The balanced three-phase circuit has a negative phase sequence. Circle your choice. (1) True (ii) False
Two single-phase transformers Trand Tz each rated at 500 kVA are operated in parallel Percentage impedances of and Tare (1 +16) and (0.8 +14.8), respectively. To share a load of 1000 kVA at 0.8 lagging power factor, the contribution of Tz (in kVA) is
Referring to the circuit shown in Figure 1 below, solve the following problems: - i) Calculate the total impedance, ZT. ii) Determine the total current, Ir supplied by the generator iii) Determine the value of current at load impedance, I1, I2 and I3. iv) Calculate total real power, PT and reactive power, Qr supplied by the generator. v) Draw a power triangle of this circuit vi) Calculate the power factor of this circuit.
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
Is it true??
For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using Newton-Raphson method. shunt line charging admittances are neglected. All the values are given in per unit on 100MVA base. Calculate the complex power flows S12 and S32 in actual units. 1) Z12 = 0.01+ j0.02 Z3 = 0.02+ j0.04 PL G QL Slack bus V2 = 0.96L -1.67° V3 = 0.884 - 5.48° Vi=1.0/0° (estimated time to answer this question: 13 minutes)
3. A circuit consists of two impedances. Z1 =20230° and Z2 =25260° 2, in parallel, supplied by a source voltage V=1002600 volts. Determine the power triangle for each of the impedances and for the source.