Q2: A spring have stiffness of 100 N/m, is fixed as shown in Fig. A 2.0 kg block mass is moved up the surface with an initial kinetic energy of 18 J, if the initial distance is 0.5m, 0= 37. Determine the kinetic energy of the box mass, at which the mass block moved up. If the block stop at the case when the spring is compressed about 0.5 m.

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: Let's consider a rod subjected to the shown axial forces. If we consider a linear elastic behavior,…

A:

Q: solve for the force in members eF and EG for the truss shown in Fig. P-4-3.14

A:

Q: where did 144 come from

A:

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: solution incorrect resolve again

A:

Q: resolve solution

A:

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are…

A: The maximum bending stress in a girder due to this load is 85 MPa.

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: y' = -y tan x, y(0) = 2

A:

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: can you answer 1B

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: Determine Stres

A:

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: The equation of the unit circle is _______________.

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.