Q2:) A rectangular settling basin is designedwith 10 m length, 5m width, and 4m depth,which treats 2000 m3/day of raw waterdaily to produce drinking water, and theinitial concentration of TSS ,2000 mg/l andother information as showed in table below,find:1) Outlet concentration of TSS? 2) Thesettled TSS 3) mass of remaining?concentration of TSS% Removal907040221710Settlingvelocity(vs)mm/s0.180.40.520.60.81

Answered: Image /qna-images/answer/688ffdd2-9287-4d7c-be91-afb0a53ef416.jpg

Q2:) A rectangular settling basin is designed with 10 m length, 5m width, and 4m depth, which treats 2000 m3/day of raw water daily to produce drinking water, and the initial concentration of TSS ,2000 mg/l and

Q2:) A rectangular settling basin is designed with 10 m length, 5m width, and 4m depth, which treats 2000 m3/day of raw water daily to produce drinking water, and the initial concentration of TSS ,2000 mg/l and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A detention basin with dimensions of width, 20 m, length, 85 m and maximum height, 4 m. receives water from an inflow hydrograph of total volume 14000 m3. The volume of water in it when the water depth is 2.5 m is A) 2550 m3 (=85 x 20 x (4 - 2.5)) B) 6800 m3, because the volume of the inflow hydrograph exceeds the maximum volume of the basin C) 4250 m3 D) 14000 m3 (the value of the inflow hydrograph)
Compute for the discharge at the outlet of canal to drain a waterlogged area of 100 ha. Drainage coefficient (rate at which water is drained from the field per day) is 10 mm. Ans. 115.7 lps.
Please write legibly, complete solutions, avoid rounding off intermediate values, thanks.
A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness coefficient is 0.013. Determine the maximum flow of the sewage the culvert may attain. (The depth of flow is 93.8% of the Diameter and 0 = 57.5867° and maximum velocity should be 82% of the Diameter.)
A discharge of 0.15 cumecs is supplied into a canal at the head and 0.1 cumecs is delivered to field having an area of 1.5 hac. The Irrigation is started at a moisture extraction level of 60% of the available moisture and then extends for 10 hours. Determine the following efficiencies: water conveyance, water application, water storage, and water distribution. The following information are known: effective depth of r.z. = 1.7 m, runoff loss in the field = 425 m3 , water penetration depth varies linearly from 1.7 m at the head end of the field to 1.1 m at the tail end, W.H.C. = 25cm/m depth of soil.
What change in velocity would be necessary if the bed was to extend by 18%?(Giving Date: Sand media size: 3 mm, operating bed depth of 0.5 m and Minimum fluidization Velocity for sand filter used in wastewater treatmen= 4 m/s, density of sand media: 2000 kg/m3 and its porosity = 0.3)
A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness coefficient is 0.013 and diameter is 0.938. Determine the maximum flow of the sewage the culvert may attain.
The water need of a district with a future population of 38800 and average daily water consumption qort = 189 lt / N / day will be met by leakage pipes fed double-sided (at the end of the collection box). Water layer thickness H = 5 m, k = 0.0018 m / s and n = 0.02 are given. Standard pipe diameters and costs are given as follows: 0.4 m (60 TL / m), 0.7 m (70 TL / m), 1.0 m (80 TL / m) and 1.3 m (85 TL / m). Size the leaking tube so that it is most economical (diameter, length and slope). Average flow velocity is between 0.2-0.4 m / s.
why do we need to know the Specific Gravity and Absorption of Fine Aggregate, Surface Moisture of Fine Aggregate, and how it is important in concrete
Given the reservoir and sections shown below, determine what is asked for. Show complete and detailed solutions. Draw a figure also.
Gave wrong values earlier. These are the correct values A settling tank having a depth of 3.5 m and surface area of 1000 m2 is used to remove particles of size 0.01 mm and specific gravity of 2.6. Calculate the removal percentage of the tank for the discharge of 7000 m3/d. Take viscosity of water as 1.1x10-3 kg/m.s.
Solve for evaporation and precipitation. If u can pls include some explanation, thankyou!