A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness coefficient is 0.013. Determine the maximum flow of the sewage the culvert may attain. (The depth of flow is 93.8% of the Diameter and 0 = 57.5867° and maximum velocity should be 82% of the Diameter.)

A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness coefficient is 0.013. Determine the maximum flow of the sewage the culvert may attain. (The depth of flow is 93.8% of the Diameter and 0 = 57.5867° and maximum velocity should be 82% of the Diameter.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A catchment consists of an asphalt pavement that drains into a rectangular concrete channel. The…

A: Given data:- The given asphalt has an average slope is, 0.6% The catchment boundary to the drain is,…

Q: 16. A rectangular sedimentation tank is to be designed for a flow of 20 million litre per day using…

Q: Flow through velocity in a horizontal flow type sedimentation tank is 0.32 m/s. If surface overflow…

Q: two sedimentation tanks operate in parallel. The combined flow to the two tanks is .1 m^3/s. the…

A: Total flow in parallel tank is equal to sum of flow in each tankFlow (Q) = Volume/detention…

Q: lar channel one metr . The 300 bed slope al

A: Given data- Discharge (Q) = 1 m³/s Width of rectangular channel (B) = 1m Depth of rectangular…

Q: Determine the time of concentration for use in the Rational Method for a drainage basin having the…

A: Average Grass Overland flow length, L = 80’ Slope, S = 2.5% Shallow Conc. L = 450’ S = 4.8%…

Q: A cuboid-shaped detention basin of dimensions width, 20 m; length, 85 m; maximum height, 4 m, is…

Q: time of concentration for

A: Using manning equation

Q: Determine the minimum discharge in the pipe for this condition. is desired to increase the discharge…

A: According to given data Two reservoirs have a minimum difference in water-surface elevation of 40 m…

Q: In a 10 m side square shaped sedimentation tank, the flow rate is 100 cum/h, and if the depth of…

A: Given that :- Dimension of sedimentation tank B = L = 10 m Depth of water = H = 2 m Flow rate = Q =…

Q: Manning's roughness coefficient of 0.013.

A: Given: Bed Slope, S = 0.0016 Manning's roughness coefficient, n = 0.013 Due to flood risk prevailing…

Q: What inputs and outputs does a life cycle analysis (LCA) of a material consider?

A: When designing a life cycle analysis (LCA), it is really important that it clearly defines the input…

Q: Design a circular sedimentation tank to treat 2500 m3 of raw water per day. The retention period…

A: The drinking water is treated with different methods based on the type of impurities in the water…

Q: calculate the appropriate dimensions for the outlet channel extending around the per meter of the…

A: calculating the perimeter of the sedimentation basin: The sedimentation basin is described as having…

Q: Find the Diameter of the runoff pipe 2 for the following area. A1=1.55*10 km? A2=1.40 102 km?…

Q: Redesign an existing rectangular storm sewer, 1.00m wide and 1.50m deep, into a circular section…

Q: Q2) A flocculation basin has dimensions of 17.4m length, 11.4m width, and 5.8m depth, with three…

Q: 0.12 A hydraulic structure is sized for a 50 year recurrence interval design discharge. What is the…

Q: Question- A circular sewer of dia 1 m carries storm water to a depth of 0.75 m. Find the hydraulic…

A: Given data- Diameter of circular sewer D = 1 m. depth of flow = 0.75 m. To Find- The hydraulic…

Q: A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness…

A: Let the diameter of the culvert be D=500 mm. The length of the culvert is L=1200 m. The slope is,…

Q: Determine the culvert size (i.e. diameter, D) required for the following design conditions: culvert…

Q: In a wastewater treatment plant, primary sedimentation tank (PST) designed at an overflow rate of 30…

Q: Two boreholes are located at points A and B along the same flowline. The soil between them has a…

A: K=3×10-5 ft/secn=40%Landfill cell- 500×100 ft To determine- 1. What is the hydraulic gradient…

Q: A circular sedimentation tank is to be designed for a flow of 50 million itre per day and the…

A: Flow = Q = 50,000,000 litre/day Over flow rate = V = 25 m3/m2.day It has been asked in the…

Q: 2. A flocculation basin is to be designed for a water treatment plant, and the design flow is 49,200…

Q: roblem I: Figure 1 shows the flow hydrograph from a storm at the watershed outlet. Label the: (1)…

Q: 4. In a wastewater treatment plant, primary sedimentation tank (PST) designed at an overflow rate of…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the discharge, to the nearest 0.01 m/s, of a 28.1-m long, circular culvert having a…

A: Following is the formula used for the calculation of discharge : Q = 1n×A×R23×S12 Here, n is the…

Q: Rapid sand filters are going to be installed in a water treatment plant. Determine how much filter…

Q: A rectangular channel has a base width of 7m and a depth of 2.5 m. carries a discharge of 21.81…

Q: A circular concrete sewer 1.52m in diameter is flowing 2/3 full has a slope of 1.22m per kilometer.…

Q: In designing a sewer an engineer selects a diameter of 300 mm and a slope that yields a velocity of…

A: Given :

Concept explainers

Drainage of Pavements

Pavement Drainage holds ample significance, as it prevents the accumulation of water or any liquid on the surface of pavements and ensures proper drainage system. With proper design and gradual slopes provided, the water gets easily removed from the surface into the drains, which are essential during heavy rains and unusual weather conditions keeping it less prone to accidents and increasing the durability of the pavement structure.

Question

A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness
coefficient is 0.013. Determine the maximum flow of the sewage the culvert may attain. (The
depth of flow is 93.8% of the Diameter and 0 = 57.5867° and maximum velocity should be
82% of the Diameter.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Calculation

VIEW

Step 3 Discharge Calculation

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4) Two box culverts each is 0.61 m by 0.61 m and has n = 0.013, Ke = 0.05, Cd = 0.85, L = 30 m, So = 0.7%, and HW = 1.5 m. What is the design flow capacity (m³/s) for tailwater of TW = 0.84 m? Answer:
An asphalt pavement drains into a rectangular concrete channel. The catchment surface has an average slope of 1.0%, and the distance from the catchment boundary to the drain is 30m. The drainage channel is 60 m long, 20 cm wide, 25 cm deep, and has a slope of 0.6%. For an effective rainfall rate of 50 mm/h, the flow rate in the channel is estimated to be 0.02 m³/s. Estimate the time of concentration of the catchment.
A wastewater treatment plant treats 750 m³/hr. of SS concentration=300mg/1 and BOD 180 mg/l. The treatment plant consists of one primary circular sedimentation tank and two single stage trickling filters. The primary sedimentation tank of surface area-500 m² and detention time 1.6 hr. Each trickling filter of depth= 2m, r=125% and BOD removal 75 %. Find: 1.Depth (m) and weir loading of the primary sedimentation tank (m³/m/d). 2.Diameter of each trickling filters (m). 3.Total BOD removal in treatment plant (%).
A flocculation basin is designed to treat a flow of 19000 m3/d. The flocculation basin has three stages. Each stage has 10-min detention time. The basin dimensions are 12 m perpendicular to flow direction, and three times the basin depth along the flow direction. Calculate: a) The total length of the basin, m b) Volume of each stage, m3.
5) Two water reservoirs are connected by a cast iron pipeline which is 150 mm in diameter for the first 6 m and 225 mm diameter for the remaining 15 m as shown in Figure 1. The entrance and exit are square-edged. If the discharge is 0.185 m³/s and dynamic viscosity of water is 0.00102 Ns/m², determine the various losses along the pipeline. Answer (2.78 m, 1.72 m, 1.1 m, 5.01 m, 1.54 m of water) H JALA B water Figure 1 C water
A 1200m circular culvert is used to carry sewage, the design slope is 3m per km and roughness coefficient is 0.013 and diameter is 0.938. Determine the maximum flow of the sewage the culvert may attain.
A weir has difference of 9 m in its water levels and there are 25 equipotential drops. The specific gravity of soil is 2.7 and void ratio is 0.67. Determine the factor of safety against piping if the flow line is 1 m long.