Q2- A rectangular concrete beam with normal weight concrete has dimensions, material strengths, and reinforcing bars given in the table below. Using the assumptions and simplifications of the ACI 318 code, determine Mn and Es. b (in.) 14 h (in.) d (in.) 18 15 fe(psi) 4000 fy (psi) 60000 As 4#11 M₂ ? Es ?

Q2- A rectangular concrete beam with normal weight concrete has dimensions, material strengths, and reinforcing bars given in the table below. Using the assumptions and simplifications of the ACI 318 code, determine Mn and Es. b (in.) 14 h (in.) d (in.) 18 15 fe(psi) 4000 fy (psi) 60000 As 4#11 M₂ ? Es ?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
Find depth of neutral axis from top fiber?
Please help by showing ALL steps I am trying to see what I am doing incorrect on don't just want the answer
Referenced concrete Using inner, not outer, triangles On the below
Please answer letter g.
Referenced concrete n=16
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
As shown below a rectangular R.C.C. column is subjected to compressive force P at an eccentricity of e. If the compression steel has yielded, the concrete has cracked and the neutral axis lies at a distance of 360 mm, calculate the limiting values P and e. 300 Asc 50 mm P. 360 mm 400 mm N.A + 50 mm st Given : (i) As = A (ii) yield stress of steel = 250 MPa (iii) modulus of elasticity = 2 x 105 MPa (iv) grade of concrete M20 = 10 cm2. %3D SC st
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 27.63 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension-controlled condition. Use the following dimensions: b = 475 mm d = 685 mm t = 138 mm web thickness = 138 mm b I NOTE: USE STORED VALUES IN YOUR CALCULATION d t