Please draw a simple restaurant plan by using autocad.

Q: Determine the reaction at B for the beam shown below. |--3m+ O a. By = 131 kN ↑ O b. By = 131 kN ↓ O…

A:

Q: A cylindrical water tower (with height 1.25 times its diameter) is vented to the atmosphere at the…

A: Given, h = 1.25 d  m = 5.25 x 105 kg H = 15 m

Q: If the distance between E and Bis h= 0.3 m, calculate the maximum absolute values of the shear and…

A: Given Data  Find maximum absolute shear force and bending moment.

Q: Determine ¯Ix for the triangular region shown. (Ans: 1.689 × 105 mm4)

A: Let 1 be the rectangle and  2, 3,  4 be the triangles.y¯=∑ay∑a  =a1y1-a2y2-a3y3-a4y4a1-a2-a3-a4…

Q: The rainfall during three successive 2 hour periods are 0.5, 2.8 and 1.6 cm. The surface runoff…

A: Given: The rainfall during three successive 2 hours period is 0.5, 2.8 and 1.6 cm P=0.5+2.8+1.6 T =…

Q: The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to…

A: The unit weight of water, γw = 9.8 kN/m3 Parabolic gate, y2 = 5x The length of the gate, L = 3 m The…

Q: A storm with 150 mm precipitation produces a direct runoff of 8.7 cm, with incremental hourly…

A: Given : Precipitation = 150 mm Direct runoff = 8.7 cm A problem of Hydrology where we are asked to…

Q: From the figure below, locate the centroid from x and y axes as shown

A: Given data in question  Composite section consisting of rectangles & triangle. Dimensions  To…

Q: A roof system has a total surface area of 3,450 sf, which will be covered by 3-tab asphalt shingles…

A: The total surface area is 3450 sf. It is known that in Asphalt 3-Tab Roof Shingles, there are 26…

Q: The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed…

A:

Q: 1. Calculate the force P on the gate to hold the gate in a closed position. The gate is 2.0 m wide.…

A:

Q: Beam subjected to moving distributed load of 4 kN/m. Maximum shear force that can occur just to…

A:

Q: An unequal angle section 200 mm x 150 mm x 15 mm is to be used in a truss as a strut of length 4.5…

A:

Q: 3. The tank shown has a parabolic curve gate at the bottom right side of length h perpendicular to…

A:

Q: A 45 cm well in an unconfined aquifer of saturated thickness of 45 m yields 600 lpm under  a…

A:

Q: A 400x12 mm steel plate has a staggered bolt hole arranged as shown. Diameter of bolt is taken as…

A:

Q: As per IS 800, the efficiency of a riveted joint having the minimum pitch is: 1. 60%

A: Problem from steel structure, Where we are asked to determine the efficiency of a riveted joint…

Q: A triangle inscribed in a semi-cirlce with radius r shown below. Locate the centroid from point O.…

A: To find centroid

Q: The consolidation rate data presented in Table 2 (next page) correspond to the 20 to 40 kPa load…

A: Given data: The initial height of the sample, Ho= 25.4 mm Drainage is provided in the both sides of…

Q: A vehicle is negotiating a horizontal curve with a velocity of 50 kmph. The width and height of the…

A:

Q: Select the lightest W for a column subjected to an axial compression load of 1000 kips. The unbraced…

A: Given Data -  Axial compression load = 1000 kips Length of the column = 10 ft  Find -  Select…

Q: Determine the reactions at supports. Also, draw the shear and moment diagram. Note: c= 8 d= 1

A: Given Data c = 8 d = 1  Find support reaction and draw shear force and bending moment diagram.…

Q: Question 6 Calculate the radius of a turn out for a data given below:- G = 1.67 m, D = 13.3 cm & N =…

A: Given- Gauge length G = 1.67 m, D = 13.3 cm & N = 12 Angle of switch Φ = 108’ The radius of a…

Q: Q3: Determine the absolute maximum live shear and absolute maximum moment in the jib beam AB due to…

A:

Q: At an axial load of 24 kN, a 50-mm-wide by 10- mm-thick polyimide polymer bar elongates 2.5 mm while…

A:

Q: Determine for the slope at support C and B, and deflection at every 0.5m interval. Take E =…

A: Lets Use MACAULAY'S Method for determining the Slope at Support B,C and Deflection at every 0.5 m…

Q: PART 3. Determine the reactions at supports. Also, draw the shear and moment diagram per member.…

A: A frame is hinged at A and the vertical roller is at E and joint D is fixed. With loading as shown,…

Q: The data below by Hermanowicz et al. (1999) slow the decay of ozone residual in treated water from…

A: Data given Contact time, Concentration of ozone residual in treated water Find : Ct that can be…

Q: Problem 2 Using slope-deflection equations, determine the end moments of the beam and column of the…

A:

Q: From the figure below, locate the centroid from x and y axes as shown. y2

A: To find centroid and total area of composite figure

Q: 2. Construct the influence line diagram for the bar force in member HK of the truss shown. Determine…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 6 7 8 9 10 11 12 13 14 15. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33. 34 35 36 37 A…

A:

Q: PART 1. Determine the reactions at supports. Also, draw the shear and moment diagram. Problem 1. [15…

A:

Q: Determine the reactions at the supports.

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Water is moving between two reservoirs at a flow rate of 0.08 m³/s via the pipes shown in the…

A: Given: D1=10cm, D2=20cm, Ks=0.08, Flow rate=0.08m3/s , L1=50m

Q: Post 8 Activity Bredessor Duration Predelſer A B с D E f ç A A H' B C 2 D.E f.G 5 7 4 10 356 4 0 2)…

A:

Q: QUESTION 6 For a horizontal curve with the following pargmeters what is the station of the PT? Give…

A: Horizontal Curve: The horizontal curve occurs at the intersection of two highways. The curve which…

Q: 5.24 Draw the shear and bending-moment diagrams for the beam and loading shown and determine the…

A: Given Data  Section W200×31.3  Draw shear force and bending moment diagram and find maximum bending…

Q: Problem 2. A [6 +2c] KN 2 m NOTE: If t B 4 m [12 + 3d] kN/m C e largest nonzero digit in your…

A: Given data,  C = 8  D = 4 Length of beam

Q: A single acting reciprocating pump has the plunger diameter of 20 cm and stroke of 30 cm. The pump…

A: A) Diameter of plunger = 20 cm  Stroke has a diameter = 30 cm Discharge from pump = 0.53 m3 per…

Q: The aquifer beneath a circular oceanic island has a mean hydraulic conductivity of 100 m d-1. Mean…

A: Given  Mean hydraulic conductivity (K0) =100 md-1  Annual recharge W0 = 1 m Year-1 = 0.00273 md-1…

Q: For equal tangent vertical curves, the horizontal distance from the BVC station to the PVI station…

A:

Q: 3. A precedence diagram network is shown below. The optimistic, most likely, and pessimistic…

A:

Q: The helical spring shown is axially loaded with a compression force P equa The mean diameter of the…

A: Given : P = 5 kN Mean diameter of spring = 100 mm To Determine :

Q: Determine the shear and moment throughout the beam as functions of x. (200+ N)lb -X- 4 ft |A. (100+…

A:

Q: You are designing an updated sanitary sewer system running through a neighborhood. A 16- inch pipe…

A: Data given Peak flow = 90 ft3/ min                  = 9060 ft3/ sec = 1.5 ft3/sec Diameter of pipe =…

Q: 1. Construct the influence line diagram for shear and moment at F of the beam shown. Determine the…

A: A beam is supported at B, C, and E and a hinge is also present at D. Degree of static indeterminacy,…

Q: Assume F₁ = 40 kN, F₂ = 50 kN, F3 = 15 kN, F4 = 50 kN, and M = 130 kN.m. 6 m H F 8 m B C M D x F₂

A:

Q: The reason for the application of the technology/concept in buildings Subject is smart windows.

A: The reason for the application of the technology/concept in buildings Subject is smart windows.

Q: For a 4,800 sf area of roof, which has numerous valleys, hips, and dormers, what would be the most…

A: For a 4,800 sf area of roof, which has numerous valleys, hips, and dormers, what would be the most…

Material Selection

A wide variety of engineering applications make use of different materials, depending upon their usage. The materials used in civil engineering vary in their properties such as strength, ductility, brittleness, and creep strength. Depending upon the application and external loading conditions, an engineer must make a wise decision for material selection. A wrong decision would fail in its functionality.