Q2) A plate 500 mmx200 mm has been placed longitudinally in a stream of crude oil of specific gravity 0.925,μ = 0.083 pa.s and kinematic viscosity of : 0.9x10* m³/s.the free stream velocity is 5 m/s .Calculate the friction drag on the plate-1 the boundary layer thickness at the trailing edge-2 the shear stress at the trailing edge -3

Q2) A plate 500 mmx200 mm has been placed longitudinally in a stream of crude oil of specific gravity 0.925,μ = 0.083 pa.s and kinematic viscosity of : 0.9x10* m³/s.the free stream velocity is 5 m/s .Calculate the friction drag on the plate-1 the boundary layer thickness at the trailing edge-2 the shear stress at the trailing edge -3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 165mm and the wall thickness is 15mm. If the air in the tank is pressurized to 18.0MPa, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: MPa MPa MPa MPa (a) Olong= Thoop= (b) Tmax= (c) Tabs max= Mi i i i
A cube of material (E = 15,000 psi, v = 0.25) of side length 2" is shown in the x, y plane. Takex positive to the right and y positive up. Determine the change in length of the cube in the three coordinate directions if 4 %3D a) The normal stress in the z direction is zero (Ans: 0.0317" in x direction) b) The normal stress in the z direction is 300 psi compression (Ans: 0.0416" in x direction) 150 psi 100 psi + 200 psi
The extruded plastic shape has dimensions of D = 27 mm, d = 23 mm, a = 100 mm, andt = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 390 N. (b) If the allowable shear stress for the plastic material is 2450 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? d a Answer: (a) TA = kPa (b) V =
The extruded plastic shape has dimensions of D = 22 mm, d = 16 mm, a = 86 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 315 N. (b) If the allowable shear stress for the plastic material is 2100 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? a Answer: (a) TA= kPa (b) V-
The extruded plastic shape has dimensions of D = 28 mm, d = 22 mm, a = 96 mm, and t = 5 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 1600 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D = 35 mm, d= 31 mm, a = 95 mm, and t = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 340 N. (b) If the allowable shear stress for the plastic material is 2250 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? d a Answer: (a) TA = kPa (b) V = N
The extruded plastic shape has dimensions of D = 22 mm, d = 16 mm, a = 92 mm, and t = 8 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 330 N. (b) If the allowable shear stress for the plastic material is 700 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d a dik
According to the elasticity modulus of the material from which the cross-section is made, whose dimensions are given in the figure, E = 200 GPa and the effective bending moment M = 50 kNm; a) Draw the normal stress distribution in the cross section. b) Unit strain rate εz at point A calculate.
A hollow circular bar of cylindrical steel is 1.5 m long and has inner and outer diameters of 40 and 60 mm. (a) What is the largest torque I can apply to the circular bar if the shear stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shear stress in the circular bar? (answers: (a) 4084.1 N.m (b) 2722.7 N.m)
The extruded plastic shape has dimensions of D=31 mm, d = 25 mm, a = 96 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 370 N. (b) If the allowable shear stress for the plastic material is 1300 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? HO D d y Answer: (a) TA = (b) V= dik a kPa N
The extruded plastic shape has dimensions of D = 26 mm, d = 24 mm, a = 90 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 355 N. (b) If the allowable shear stress for the plastic material is 1000 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D = 31 mm, d = 25 mm, a = 93 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 375 N. (b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d A a Answer: (a) TA = kPa (b) V =