Q2/ A metal plate of 4mm thickness (k = 95.5 W/m°C) is exposed to vaporat 100°C on one side and cooling water at 25°C on the opposite side. Theheat transfer coefficients on vapor side and waterside are 14500W/m^2°C and 2250 W/m^2 °C respectively. Determine the overall heattransfer coefficient * Q1/ The center to surface temperature difference in a heat generatingcylindrical rod of 4 m diameter was 30°C. What is the differencetemperature between the center and surface in the case of a sphere of 2m diameter under similar conditions? *Your ancwer

2) Metal plate thickness, t=4mm=0.004m Thermal conductivity of the plate, kp=95.5 W/moC Vapor…

Q2/ A metal plate of 4mm thickness (k = 95.5 W/m°C) is exposed to vapor at 100°C on one side and cooling water at 25°C on the opposite side. The heat transfer coefficients on vapor side and waterside are 14500 W/m^2°C and 2250 W/m^2 °C respectively. Determine the overall heat transfer coefficient

Q2/ A metal plate of 4mm thickness (k = 95.5 W/m°C) is exposed to vapor at 100°C on one side and cooling water at 25°C on the opposite side. The heat transfer coefficients on vapor side and waterside are 14500 W/m^2°C and 2250 W/m^2 °C respectively. Determine the overall heat transfer coefficient

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The steam pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe that needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam only decreases slightly to 95%. The temperature of the outer surface of the insulation is assumed to be 25 ° C. The conductive of the pipe material and the situation of no pressure drop in the pipe. A. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam that comes out = Answer kJ / kg. c. Determine the change / loss of steam heat along the flow = Answer watt. d. Determine the minimum required insulation thickness = Answer cm.
t = 30 + 0.9563 (62.2- 30) = 60.79°C (Ans.) Example 4.14. A very thin glass walled 3 mm diameter mercury thermometer is placed in a stream of air, where heat transfer coefficient is 55 W/m2°C, for measuring the unsteady temperature of air. Consider cylindrical thermometer bulb to consist of mercury only for which k and a = 0.0166 m2/h. Calculate the time required for the temperature change to reach half its final or, %3D 8.8 W/m C %3D value.
700 W/m3 electrical heat is generated in a large plane wall whose one side is insulated while the other side is subjected to convection. The thermal conductivity of the wall is (k W/m.K) and the convection heat transfer coefficient is (h = 17 W/m?K). Determine the location and the value for the maximum temperature and the minimum temperature in the plate for steady one-dimensional heat transfer. Assume T. = 25°C. A=1 m?; L= 25 cm). = 20
Steaks (2 cm thick, k = 0.45 W/m - °C, « = 0.91 x 107 m2/s) usually have an original temperature of 25 °C. They will be cooled in a refrigeration room. The said room has a temperature of -11 °C. The heat transfer coefficient on both sides of the steak is 9 W/m2 - °C. How long will it take for both surfaces of the meat to be cooled to 2 °C? Assume the geometry of steaks to be a flat slab.
The flow of water entering a pipe is 0.25 kg / s and its temperature is 20 ° C. The diameter of the pipe is 20 mm and the wall temperature of the pipe is 100 ° C. If the average value of the heat transfer coefficient is 700 W / m C, what is the length of the pipe required to raise the water temperature to 80 ° C?
I need the answer as soon as possible
. Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k = 2.3 W/m °C, and surface area A = 20 m². The left side of the wall is maintained at a constant tem- perature of T₁ = 80°C while the right side loses heat by con- vection to the surrounding air at T = 15°C with a heat transfer coefficient of h = 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat trans- fer through the wall. Answer: (c) 6030 W
Water flows through a cast steel pipe with k = 53 W/m-K with an outer diameter of 110 mm and 3.5 mm wall thickness. Calculate the thickness of insulation to be lagged on the pipe if the heat transfer per unit length is 6.5 W/m. The thermal conductivity of the insulation is 0.045 W/m-K. The water temperature is 15°C with convective heat transfer coefficient of 30 W/m2 -K while the outside air is -8°C and 18 W/m2 -K.
Design a solar chimney to cover 75% of total heating losses, where U value for the chimney=0.5 W/m2.K and the total wall area of the spaces equal 70m2 and the temperature outside are 5oC at night and 8oC at day and the temperature for the interior is 24 oC.
Please help with assumptions and fbd
A house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.
A 0.5-ampere current is flowing through a long electrically conducting cylindrical rod. The diameter of the rod is 6 mm, the electrical resistance of the rod is R = 2000 /m, and k =0.9 W/m K for the rod. The rod is encased in a 2-mm thick Pyrex tube and a 20°C liquid is flowing over the outer surface of the Pyrex tube. The convection heat transfer coefficient for the liquid h= 800 W/m2 . K. The interfacial conductance (contact resistance) at the interface between the rod and the Pyrex tube is h = 1200 W/m² - K. a) Compute the rate of heat generation in the rod and use it compute the volumetric rate of heat generation. b) Find the temperature drop across the interface between the outer surface of the rod and the inner surface of the Pyrex tube. c) Find the temperature at the center of the rod.