Q2) A long, bare, thermocouple wire having a diameter of 1.0 mm is attached to a ceramic solid having a density of 2400 kg/m³, specific heat of 650 J/kg - C, and a thermal conductivity of 0.85 W/m - C. The conductivity of the thermocouple wire is 75 W/m - C and it is exposed to an environment with h = 275 W/m² - C and a temperature of 50°C. The convection coefficient to the ceramic is 25 W/m² - °C. The indicates a temperature of 220°C. What is the true temperature of the thermocouple solid?

Q2) A long, bare, thermocouple wire having a diameter of 1.0 mm is attached to a ceramic solid having a density of 2400 kg/m³, specific heat of 650 J/kg - C, and a thermal conductivity of 0.85 W/m - C. The conductivity of the thermocouple wire is 75 W/m - C and it is exposed to an environment with h = 275 W/m² - C and a temperature of 50°C. The convection coefficient to the ceramic is 25 W/m² - °C. The indicates a temperature of 220°C. What is the true temperature of the thermocouple solid?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2) Solve the following values in figure 2.0. a) Total capacitance, Ct b) Total charge, Qt c) Individual charge of (a) C1 (b) C2 (c) C3 FIGURE 2.0 A 12 10V :C1 :C2 :C3 TuF 2uF 3uF B•
None
An 18-gauge copper wire with a diameter of 1-mm carries a constant current of 1-A. The charge concentration in the wire is 8.5 x 1028 per cubic meter. Determine the resistance, in ohms, of a 77-m wire in milli-ohm. Use resistivity equal to 1.72x10-8 ohm-m.
1-1)The length of Copper wire is 10m and its cross-sectional area is 0.5mm2 has a Calculate: resistance 0.34SN. a) The conductivity of Copper wire. b) the mobility of electrons in the copper wire.
B) Define the permeability (ur) of the material. If you are required to design IH and IpH inductors, what type of core will you use in your design and why? support your answer by equations.
explain in a summarized form the procedures for the calculation of elements for the construction of a PROTOTYPE OF PIEZOELECTRIC TILE FOR THE GENERATION OF ELECTRIC ENERGY THROUGH THE PEDESTRIAN TRAFFIC
For a non-uniformly doped semiconductor sample, the sheet- 1 resistance is given by: R =- aju(x)n(x)dx For the three n-type thin layers on a p-type substrate shown in the Figure, determine Rh- (n=1250 cm²/V/s, q=1.6 × 10-¹⁹ C) n (cm-³) 1016 10¹5 0 n (b) (a) (c) 104 P x (cm)
Compare the dependence on temperature for electrical conductivity in metals and semiconductors intrinsic, explaining the difference in behavior.
Ex
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm
Q4/ Find the conductivity of Si that is doped with 2 parts per 108 of donor impurity. Given that there are 5 x 1028 m Si atoms Hn = 0.13 and V. Sec Hp = 0.05 V. Sec