Q2: A cantilever 1.5 m long is loaded with a uniformly distributed load of 2kN/m run Over a length of 1.25 m from the free end. It also carries a point load of 3kN at a distance of 0.25m from the free end. Draw the shear force and bending moment diagram of the cantilever. 3 kN 2 kN/m 0.25 m 1m 1.5m 1.25 m 0.25 m

Q2: A cantilever 1.5 m long is loaded with a uniformly distributed load of 2kN/m run Over a length of 1.25 m from the free end. It also carries a point load of 3kN at a distance of 0.25m from the free end. Draw the shear force and bending moment diagram of the cantilever. 3 kN 2 kN/m 0.25 m 1m 1.5m 1.25 m 0.25 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam below, (a) draw the shear and moment diagrams and (b) determine the maximum normal stress in the beam due to bending. 20 kN A B -2.5 m-3 m 40 kN C -2 m- D 250 mm 80 mm
18
Give me the solutions of this. Identity the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m
.
U2
Determine the value of bending moment in column 2 (in kip-ft, absolute value) if the bay width is 21 ft the story height is 11 ft and the load P is 2.2 kips. P 1 2 3
Situation 2 Determine the force in kN of following-member of the loaded truss. Indicate whether it is C (Compression) or T (Tension) 1. Reaction at E 2. CD 3. JK 60 kN 60 kN 11m 2 m 4. 3 m G- C 75 kN 75 kN 75 kN 6 at 4 m = 24 m
A propped cantilever beam with a lengthL = 4 m is subjected to a trapezoidal load with intensitiesq0 =10 kN/m and q1 =15 kN/m. Find the reactionsat A and B. Hint: The loading is the sum ofuniform and triangular loads.
For the beam shown below: 1- Draw the shear and moment diagrams. 2- Determine the absolute maximum bending stress in the beam. 50 KN 5 kN-m 5 kN-m 12 + A- -1 m- m- m B -1 m- 150 mm 250 mm
%3D Given: w1 = 50 kN/m, w2 = 30 kN/m, P = 30 kN, a 3 m, b= 3 m, and c 3 m. Determine the maximum %3! moment in kN-m. Neglect the mass of the beam. P kN w1kN/m w2kN/m b m C m a m R2 R1
A beam with a wide-flange cross section (seefigure) has the following dimensions: b =120 mm,t = 10 mm, h = 300 mm, and h1 = 260 mm. The beamis simply supported with span length L = 3.0 m.A concentrated load P =120 kN acts at the midpointof the span.At a cross section located 1.0 m from the left-handsupport, determine the principal stresses σ1 and σ2and the maximum shear stress τmax at each of thefollowing locations: (a) the top of the beam, (b) thetop of the web, and (c) the neutral axis.
A simply supported beam spans 8 m. the cross section width is 300mm, the effective depth is 500mm. It is required to carry a uniformly distributed load of 150 kN/m at ULS. Assume fe=30 MPa and fuk=500 MPa. Design the beam for both bending and shear.