Q2/ (30) Water flows steadily through the 0.75-in.-diameter galvanized iron pipe system shown in figure at a rate of 0.020 ft/s. Your boss suggests that friction losses in the straight pipe sections are negligible compared to losses in the threaded elbows and fittings of the system. Do you agree or disagree with your boss? Support your answer with appropriate calculations. Hint: compare the major loss with minor loss and decide if you agree or disagree with your boss's idea. 6-in. length 6-in. length 90° threaded elbows - 0.60-in. dia. Q = 0.020 cfs Reducer -1-in, length 4-in, length Tee Closed ball valve

Q2/ (30) Water flows steadily through the 0.75-in.-diameter galvanized iron pipe system shown in figure at a rate of 0.020 ft/s. Your boss suggests that friction losses in the straight pipe sections are negligible compared to losses in the threaded elbows and fittings of the system. Do you agree or disagree with your boss? Support your answer with appropriate calculations. Hint: compare the major loss with minor loss and decide if you agree or disagree with your boss's idea. 6-in. length 6-in. length 90° threaded elbows - 0.60-in. dia. Q = 0.020 cfs Reducer -1-in, length 4-in, length Tee Closed ball valve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Explain the major and minor losses? Then solve for the parallel pipes system shown below, a pump is placed in line 2 so that 0.142 m³/s will flow through each pipe. Pipe material is cast iron and for each elbow. Find the relation between the head loses hL1 and h12 and estimate the necessary pump head. Water viscosity is μ=1x10-³ Pa.s. Line 1, L-30 m, D= 6 inches Q₁-0.142 m³/s Pump Line 2, L, 30 m, D-3 inches Q-0.142 m/s R
State clearly your assumptions in your solution sheet
please help me with this exercise ...
A major water main is an 18-in ductile iron pipe. Compute the Reynolds number if the pipe carries 16.5 ft/s of water at 50°F.
I need the answer at 20 minute
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
Question 3 Water flows through a 2-in.-diameter (5.08 cm) tube that suddenly contracts to 1 in. diameter (2.54 cm). The pressure drop across the contraction is 3.45 kPa. Determine the volume flow rate. Minor Loss Coefficients for Pipe Entrances Entrance Type Reentrant Minor Loss Coefficient, Ka 0.78 Square-edged Rounded "Based on h-K(V2/2), where V is the mean velocity in the pipe. Contraction loss coefficient, K [ h = Kc \ /² ] 0.5 r/D K 0.02 0.06 ≥ 0.15 0.28 0.15 0.04 Contraction Expansion A1 A2 A₂ AR Ag/A = AR = A₁/A2 1.0 0.8 0.6 0.4 0.2 0.2 о T ° 0 0.2 0.4 0.6 0.8 1.0 Area ratio, AR 1.0 OOOO 0.8 0.6 Expansion loss coefficient, K Loss coefficients for flow through sudden area changes.
Kindly solve with full solution and explain. Thank you very much
Water at 80°F flows from a storage tank through 618 ft of 6-in Schedule 40 steel pipe, as shown in the figure. Taking the energy loss due to friction into account, calculate the required head hin feet above the pipe inlet to produce a volume flow rate of 1.65 ft³/s. (round the final answer to three significant figures) h 6-in Schedule 40 steel pipe pipe length
6-1 Determine the flow rate through the Venturi meter shown in the diagram if the ideal conditions exist. P₁ = 735 kPa Q 31 mm P₂ = 550 kPa 19 mm y=9.1 kN/m³
Question 3 A pipe of 150mm bore is delivering water at the rate of 7500 dm/min at a pressure of 820 kN/m?.It connects by a gradually expanding pipe to a main of 300 mm bore which runs 3m above it. Find the pressure in the 300mm main?