I need the answer as soon as possible Q2: 1- A centrifugal pump is to be operated with discharge 2.5 m3/min. If the power needed for the motoris 15 KW, compute the total head of the pump if the efficiency of the motor is 70% and the pump efficiencyis 80%.Pali2- For the above question, if you know the atmospheric pressure is 96 kpa, vapor pressure is 15.3 kpa andthe required NPSH is 48 kpa, what will be position of the pump such to avoid cavitation. Neglect losses.

Compute the total head of the pump,H=?

Q2: 1- A centrifugal pump is to be operated with discharge 2.5 m3/min. If the power needed for the motor is 15 KW, compute the total head of the pump if the efficiency of the motor is 70% and the pump efficiency is 80%.

Q2: 1- A centrifugal pump is to be operated with discharge 2.5 m3/min. If the power needed for the motor is 15 KW, compute the total head of the pump if the efficiency of the motor is 70% and the pump efficiency is 80%.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2/100 The driver of the truck has an acceleration of 0.4g as the truck passes over the top A of the…

A: step 1-

Q: Consider the following arrangement: A B String ww www Steel cube

Q: Determine the force in each member of the loaded truss. A 60° 45° C 15° W B

Q: lution so i c

A: Apply Bernoullis theorem P1γw+v122g+z1=P2γw+v222g+z2we knowP1=P2=Patm=0v1=0 (as large dia)

Q: Q3: Refer to the soil profile shown in the figure below: a) Calculate the variation in vertical…

Q: A rectangular plane surface of width 2 m and height 3 m is placed vertically in water. What will be…

A: given- width b=2 mheight h=3 m

Q: Situation 1: A W8x67 has a length of 7.50 m. Fy- 248 MPa. The properties are given below. Properties…

Q: H.W1 The beam is subjected to the linearly varying distributed load. Determine the maximum…

Q: A steel bar is placed between two copper bars, each having the same area and length as steel bar at…

A: This question is related to the Strength of Material.

Q: SOLVE THE INDETERMINATE STRUCTURE USING THE MOMENT DISTRIBUTION METHOD AND SHOW A COMPLETE SOLUTION.…

A: Given An indeterminate beam having support A and D as pin and support B and C as roller. Required…

Q: Compute the cooling load for the south windows on a middle floor of an office building that has no…

A: Given :

Q: water-cement ratio needed for the design mix?

A: As per ACI design mix procedure In air entrained concrete for the strength of concrete 5000psi,…

Q: Rigid bar ABC is supported by two identical solid bronze [Oy = 331 MPa; E = 105 GPa; a = 22.0 ×…

Q: 6 m B 240kN/m 6 m 4.5m 750kN/m D

Q: Es width of 2 m relative densit

A: given:

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

A: Given E= 200 GPa , I= 39.9 × 10-6

Q: H.W4 Determine the slope of the simply supported beam at A and deflection at C. E = 200 GPa and I =…

Q: For a shallow foundation shown below: Estimate the ultimate bearing capacity when the water table…

A: Answer Let us use Terzaghi's Bearing capacity equation for rectangular footing to calculate the…

Q: b) List factors which affect the quantity of storm water flow for design of sewer system?

A: This question is related to the Hydrology Engineering. In this question ask only for listing factors…

Q: If the gauge pressure and atmospheric pressure at a point are observed as 70 mm of mercury and 750…

A: Given data: Gauge pressure = 70 mm of mercury Atmospheric pressure = 750 mm of mercury

Q: Problem 1: A soil profile is shown in the figure. A uniformly distributed load of 4b kPa is applied…

Q: 12 kN/m -4 m B -4 m -4 m- 12 kN/m D

Q: The lowest stress at which permanent .deformation can be measured

A: Brief Concept Introduction- Stress- It is the ratio of the force acting on a cross-section and the…

Q: F 2.5m 200 t N/m 2m 300 N 1.5m | 250 mm F 100 mm 30 mm | 1.5m| 2m 50 mm 250 N/m E = 18 GPa

Q: 4/4 Determine the force in each member of the truss. Note the presence of any zero-force members. 5…

A: To find force in all members of the truss

Q: Determine the force in member BE. State whether the member is in tension or compression. Set P = 10…

Q: The steel framework is used to support the 5-in. reinforced stone concrete slab that carries a…

Q: An aluminum pipe has a length of 50 m at a temperature of 6°C. An adjacent steel pipe at the same…

A: Concept Initial length = L1 at temperature T1 Due to temperature change to T2 length of the…

Q: With normal barometric pressure at sea level, the atmospheric pressure at an elevation of 1215.5 m…

A: Archimedes' principle states that a body immersed in a fluid is subjected to an upwards force equal…

Q: A coagulation treatment plant with flow of 0.5 metre cube per second is dosing alum at 23 milligram…

Q: Obtain the general solution of the DE: (xy + x) dx = (x²y² + x² + y² + 1) dy x)dx…

A: Given data: xy+xdx=x2y2+x2+y2+1dy

Q: Problem II. Refer to the beam shown below. q (kN/m) = 21 q (kN/m) P (kN) = = 94.50 -6 m- 3 m- a)…

Q: omplete s

Q: Q2/ setting out of curve by perpendicular offsets from tangent lines when deflection angle of…

Q: Calculate the nominal and reduced moment capacities for the indicated concrete sections. Given:…

A: Here is the solution of first two figures. Due to time shortage can't solve 3rd figureGiven data: fc…

Q: The boat is pulling three water skiers. Skier A makes an angle of 30° with the boat driving…

A: FV=FAsin30°+FBsin5°-FCsin15°=900sin30+900sin5-900sin15=295.503N

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A: For the given bell crank:

Q: Given the following data from a differential levelling survey conducted in a certain road site,…

Q: 70 The center of mass G of a high jumper follows the trajectory shown. Determine the component Up,…

Q: 1. If E = 2 GPa and I = 300,000,000 mm4. Support A settles by 10mm and support B settles by 20mm.…

A: EI = 2 × 103 × 3 × 108 = 6 × 1011 Nmm2 EI = 600 KNm2 ∆A = 10mm = 0.01 m ∆B = 20mm = 0.02 m

Q: Two wooden members, each having a width of b = 6.0 in. and a depth of d = 2.0 in., are joined by a…

Q: 52. If the unsupported length of a stanchion is 4 meters and least radius of gyration of its cross-…

A: given- unsupported length Leff=4 m= 400 cmrmin=5 cm

Q: (b) Identify the two (2) broad categories of sampling methods and name two 2) types under cach

A: There are two types of the sampling methods. They are 1. Probability sampling 2. Non-probability…

Q: the stresses in bars (1) and (2). the vertical deflection vp of point D on the rigid bar. the load…

Q: A simply supported beam 4 m long is carrying a variable load of w = 0 KN/m at the left support and w…

Q: 2. A connection is made from two 1.9 cm bolts in parallel, placed on a 21.6 cm wide steel bar. The…

A: Given data:- Diameter of bolts,d = 1.9 cm Thickness of steel bar, t = 2.54 cm Ultimate strength of…

Q: Determine the value of void ratio if porosity is 0.402 a:0.65 b:0.69 c:1 d:0.67 e:None of the above

A: Given data in question Porosity To find out Void ratio

Q: Determine the size of the column base plate if the foundation where the steel column will be placed…

Q: 10. A steel gate 2.0 m high and 1.6 m wide has its topmost side 1.4 m below the water surface. What…

Q: An aluminum alloy [E = 73 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P.…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

Q2: 1- A centrifugal pump is to be operated with discharge 2.5 m3/min. If the power needed for the motor
is 15 KW, compute the total head of the pump if the efficiency of the motor is 70% and the pump efficiency
is 80%.
Pali
2- For the above question, if you know the atmospheric pressure is 96 kpa, vapor pressure is 15.3 kpa and
the required NPSH is 48 kpa, what will be position of the pump such to avoid cavitation. Neglect losses.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 5: For system shown below, estimate: 1. The head, flow rate, and efficiency in case of combined pumps in parallel and series 2. At which configuration should the system be operated? 3. In case pump 2 is turned-off, estimate the shut-off head and free delivery flow rate in the system 20 Hp (m) 40 100 80 60 -Pump 2 Pump 1 Efficiency curve 100 200 Combined in series Combined in parallel 300 Eff. 90% 80% 70% 60% 50% 40% 30% 400 Q(L/min)
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (f) actual work of the pump if pump isentropic efficiency is 89% (g) actual turbine work if turbine isentropic efficiency is 90%
A. For the system shown in the figure, select the proper pump that has the best efficiency to raise 12 m³ of water from the lower tank to the upper one. The time targeted for the process to be completed at least in 60 mins. The pump is located at zero elevation. Make your calculations at the minimum allowed depth in the lower tank (i.e. 1 m). What would be the efficiency and actual flow rate? Head (m) 35 30 25 20 15 B. Using your recommended pump, how long does it take the pump to elevate 12 m³ if the water level in the lower tank is fixed at 3 m. 40 10 5 0 - 0 Pump 3 Pump 2 Pump 1 0.001 Max: +3 m 0.002 Min: +1 m I I 60% 70% 80% 90% T I 1 I I + T 1 I I + I CHw = 150 D = 100 mm 0.003 Flow (m³/s) T I I + 1 T L=10 m +16 m 0.004 L = 16 m ooo oo ロロ 0.005 0.006
150 mm d Hg Problem 4.96 Problem 4.95 4.96. One hundred and twenty litres per second of jet fuel (JP-4) are flowing. Calculate the pump power.
A very long garden hose has an internal vol- ume of 2.7 gal. If the garden hose is initially empty, and the faucet is opened instanta- neously to produce a flowrate of 1.6 gal/min, how long does it take to fill the garden hose and a 5-gallon bucket?
Determine the shaft horsepower for an 80% efficient pump to discharge 30L/s through the system. The system losses, exclusive of pump losses, are 12V2/2g and H = 16m. Ans: 8.75hp H 150mm dia
A pipe hose should deliver at least 1200 lpm. If the nozzle has a diameter of 30 mm, what is the velocity of the issuing jet?
Q4// A centrifugal pump is to operate against a total head of 300 kPa and is to discharge 50 m/hr. Compute the water power and motor power assuming an efficiency of 70 percent. If the efficiency of an electric motor is 80 percent.
If the velocity of water is 8m/s and the pressure is 140kPa on the discharge side of a pump. How much power (in horsepower) is required to drive it if the diameter of the suction side is 600mm? If the pump is rated at 190hp, what is the efficiency of the pump neglecting energy losses in the system? Use diameter of pipe on discharge side equal to 50cm and the pressure on the suction side of the pump is 90kPa.
A fire hose nozzle has a diameter of 1.125 in. According to some fire codes, the nozzle must be capable of delivering at least 250 2.750-in.-diameter hose, what pressure must be maintained just upstream of the nozzle to deliver gal/min. If the nozzle is attached to a this flowrate? Answer p= i psig
1.) Compute the specific speed for a pump operating at 4000 rpm delivering 600 gal/minof water at a total head of 150 ft.
As the project engineer for your consulting firm, you are in charge of designing a flocculation tank to treat municipal drinking water. The design flow for the plant is 0.050 m3/s. The average water temperature is 10oC. The following design assumptions for the flocculation basin have been made:Number of tanks = 1Number of compartments in tank: 3Tapered G in 3 compartments: 60, 50, and 20 s-1Detention time = 30 min for entire flocculation basinDepth = 3 mTanks will have a square compartment plan (overhead) view1 Horizontal shaft paddle wheel per axis will be usedPaddle wheels will have 4 arms and 2 blades/armPaddle blades are 3 m long by 0.6 m wide. Assume blade spacing (diameter) of 1 and 2 m. Design the flocculation tank by providing the following for the first two compartments only:a) Tank and compartment dimensions in mb) Water power input in kWc) Rotational speed of the paddle wheel shaft in rpm