Q1:The volume of a liquid is calculated by allowing the liquid to flow into a cylindrical tank (stood on its flat end) and measuring the height of the liquid surface before and after the liquid is given by: V= n (h, - h,) 2. (d/2)? ,lf h, = 2m, h,= 3m and d = 2m with error 1% for each , what is the uncertainty of * ? volume

Q1:The volume of a liquid is calculated by allowing the liquid to flow into a cylindrical tank (stood on its flat end) and measuring the height of the liquid surface before and after the liquid is given by: V= n (h, - h,) 2. (d/2)? ,lf h, = 2m, h,= 3m and d = 2m with error 1% for each , what is the uncertainty of * ? volume

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Need Solution through 15min
Determine the resistance in each scenario presented. Explain whether the resistance is linear or not, and if not describe the relation, finally, explain how it can be linearized about a specific condition. Be sure to state the units and demonstrate that they are correct using the appropriate pressure/flow relation. a) Laminar flow An aqueous solution of 50% glycerol / 50% water is flowing through a pipe with the following system parameters: System_Parameters = (L = 100.0 D= 0.2 u= 0.022 p= 1150.0 9m=7.0 g = 9.81) units : L ~ m; D~ m; µ ~ Pa · s; p~ kg: 4. ~ 8: Confirm that this is laminar flow and then calculate the resistance. b) Pump Resistance from Pump Curve Consider the following pump curve: [Feet) (Meters] 30어 Find the pump resistance if the pump is supporting 15 meters of discharge head pressure, at a flow rate of 300 L/minute. 80- 250 7어 100 PSI L/min Determine the pump resistance in Pa 20어 6어85 PST 50 SCFM 5어 75 PST Note that standard pump curves are oriented opposite to the…
In mechanical fluid
Please I want answer for this question - 7 . Many Thanks
Question 2: The pressure drop, AP, in a horizontal pipe depends on the pipe diameter, d, pipe length, L, pipe roughness, ɛ, average velocity, V, density of the fluid, p, and absolute viscosity of the fluid, u. Express the variables in non-dimensional form using Buckhingham-Pi theorem
Provide answer step by step.... Thank you
Q) The velocity v (m/s) of air flowing past a flat surface is measured at several distances y(m) away from the surface. Use Newton'sviscosity law to determine the shear stress t (N/m³) at the surface (y=0). dv 'dy Assume a value of dynamic viscosity =1.8* 10- N.s/hm² y, m V, m/s 0.002 0.287 0.006 0.899 0.012 |1.915 0.018 3.048 0.024 4.299 (r-7) Use two forward đifference approximations for h=0.006. Estimate the approximate percent relative error, &. b- , (t=?) Use two forward difference approximations with a step size of 0.012 (h=0.012). Estimate the approximatepercent relative error, , e.. (r-?) ApplyRichardson extrapolation. Estimate the approximate percent relative error, & (r=?) Use unequally spaced three data and the first-derivative of a second-order d- Langrange polynomial to evaluate the derivative (y=0) and shear stress. Estimate the approximate percent relative error, Eg Compare the approximate estimates of the error ([ed ) for the formulas used.
He Will GOUDIE, Question 9 (1 point) 4) Listen When the temperature remains constant, the relationship between pressure an volume can be expressed by P2-(P1 x V1) / T2. P2 (P1 x V1)/V2. P2 (P1 x T1)/V2. P2-V2/(P1 × V1), - Question 10 (1 point) ✓ Saved 4) Listen Which of the following is true, assuming that temperature remains constant? se by h
Flow (m³ /h) 1 1.5 2 2.5 Pressure difference Ap (bar) 0.005 0.012 0.021 0.034 Kinematic viscosity 10-6 m?/s V (Rough Pipe Radius = 25mm) (Rough Pipe length =L=80cm) Question: An experiment is made using different flow rates in a pipe and pressure differences are given according to the given flow values. According to these; 1. Calculate the pipe roughness height ( e ). 2. Calculate the Reynolds value. 3. Calculate the coefficient of friction f from the Darcy-Weisbach equation. 4. Briefly describe the equations you use and the reasons for using them.
5. As part of a pollution study, a model concentration c as a function of position x has been developed, c(x)=A(e-x/2a-e-x/a) where A-10-5 ppm (parts per million) and a=1 m. Plot this concentration from x-0 to .x= 10 m. If a vehicle with a pollution sensor travels through this atmosphere at u-U (U=10 m/s), develop an expression for the measured concentration rate of change of c with time, and plot using given data. (a) At what location will the sensor indicate the most rapid rate of change? (b) What is the value of this rate of change?