i need the answer quickly (Q1]Show that1- The Gain of a first-order low pass filter at any frequency f is givenby:VoutApVoltage Gain, (Av)Vin1+fcWhere:Ap = the pass band gain of the filter, (1 + R2/R1)f = the frequency of the input signal in Hertz, (Hz)fc = the cut-off frequency in Hertz, (Hz)2-At f=fc, the voltage gain is given byl'outl'oltage Gain. (.4v) =V'in

We need to design active low pass filter .

(Q1]Show that 1- The Gain of a first-order low pass filter at any frequency f is given by: Vout Ap Voltage Gain, (Av) Vin fc Where: Af = the pass band gain of the filter, (1 + R2/R1) f = the frequency of the input signal in Hertz, (Hz) fc = the cut-off frequency in Hertz, (Hz) 2-At f=fc, the voltage gain is given by l'out l'oltage Gain. (4v) = V'in

(Q1]Show that 1- The Gain of a first-order low pass filter at any frequency f is given by: Vout Ap Voltage Gain, (Av) Vin fc Where: Af = the pass band gain of the filter, (1 + R2/R1) f = the frequency of the input signal in Hertz, (Hz) fc = the cut-off frequency in Hertz, (Hz) 2-At f=fc, the voltage gain is given by l'out l'oltage Gain. (4v) = V'in

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
i need the answer quickly
The is the distance from-1 the centre of one slot to the centre of .the next slot a) coil span O b) pole pitch O c) slot pitch O
Give information regarding the Heading Indicator. >History >Development and Timeline>Application >How it works>Regulations
For the following switch circuit: A) Derive the switching algebra expression that corresponds one to one with the switch circuit. B) Derive an equivalent switch circuit with a structure consisting of a parallel connection of groups of switches connected in series. (Use 8 switches.) C) Derive an equivalent switch circuit with a structure consisting of a series connection of groups of switches connected in parallel. (Use 7 switches.)
I need the answer as soon as possible
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
I need the complete solution & explanation pls