Q19. As shown in the image below, the 2.7-Mg four-wheel-drive SUV tows the 1.1- Mg trailer. The traction force developed at the wheels of the SUV is FD = 11 kN. Determine the tension force (in kN) developed in the coupling, A, between the SUV and the trailer. Neglect the mass of the wheels, and also, the wheels of the trailer are free to roll (no traction). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. 63 Your Answer: A FD

Q19. As shown in the image below, the 2.7-Mg four-wheel-drive SUV tows the 1.1- Mg trailer. The traction force developed at the wheels of the SUV is FD = 11 kN. Determine the tension force (in kN) developed in the coupling, A, between the SUV and the trailer. Neglect the mass of the wheels, and also, the wheels of the trailer are free to roll (no traction). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. 63 Your Answer: A FD

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.59P: How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull...

See similar textbooks

Similar questions

Y F1 α В X F2 You and your friends are planning to move the log. The log. needs to be moved straight in the x-axis direction and it takes a combined force of 2.9 kN. You (F1) are able to exert 610 N at a = 32°. What magnitude (F2) and direction (B) do you needs your friends to pull? Your friends had to pull at: magnitude in Newton, F2 = direction in degrees, ẞ = N deg
Q1// For the system shown below, determine the magnitude & direction of : 1- The resultant force (F ) of the forces F1,F2 & F3 . Where F1= 1ON „F2= 15N „F3= 20N 2- The resultant force (T ) of the forces T1,T2 & T3. Where T1= 25N „T2= 10N ,T3= 15N. 3- The resultant force (R) of two forces F &T. F3 45 60 30 45 T2K F2 ---Y
Please help explain the annotation?
The figure shows the biomechanical model of a sprinter's foot just before starting a race. Determine the magnitude of the force exerted on the heel by the Achilles tendon, FH, and the magnitude of the force exerted on the foot at the ankle joint, FJ. Also indicate what type of lever it corresponds to and the MA (mechanical advantage) ratio for the configuration shown.
I did not understand this meaning
Need help
F y A → X CC BY UBC Engineering Your team is prototyping a simple braking system for your model car. The 2.2 kg wheel with a radius of rad r = 0.25 m is rotating at w = 5 A servo motor can apply a variable force F, which in its first two seconds of operation is equal to F N. If the coefficient of kinetic friction between the braking arm and the wheel is uk 10t N and afterwards is equivalent to a constant force of F = 20 0.25, determine the time needed for the wheel to come to a full stop. The point of contact P between the wheel and the - 0.2 i + 0.24 j m from point A. The force of the servo motor is applied at arm is a distance r P A exactly half of the horizontal distance to A from the point of contact. Assume the wheel can be treated as a disk and that the braking arm is massless. B
A block sits on a plane, and there is friction between the block and the plane. The plane is accelerated to the right. If the block remains at the same position on the plane, which of the following pictures might show the free-body diagram for the block? (All of the vectors shown are forces.) N (zero force) Fi та та mg mg mg mg
2. An automobile and its load weigh 22.5 KN and the center of gravity is 0.60 m above ground level and midway between the front and rear wheels, 2.44 m apart. The car is brought to a complete stop from a speed of 96.5 km/hr in 10 seconds by means of the breaks. Find the normal pressures on each of the front and rear wheels. Let NF = normal pressure on one front wheel REF = reversed effective force = a NR = normal pressure on one rear wheel REF 0.60 m R F 1.22 m 1.22 m 2NR 2NF
Let F1, F2, F3 and F4 be four forces acting on a dimensionless particle. The force F4 represents the tension generated in a cable connected through a pulley without mass or dimensions to an object of mass M hanging vertically. y F1 Draw the free-body diagram for the system, labeling the x, y components of the appropriate vectors. F2 10° 20° Let F1 = 200N, F2 = 400N, F3 = 350N, calculate the x, y components of the forces F1, F2 and F3. 3 %D F4 4 5, Calculate the modulus of the resultant of the sum between F1, F2 and F3. F3 Find the angle between the positive x-axis and the resultant force counterclockwise.
Help!! Answer correctly
An eye bolt is used to attach 3 cables to a steel plate. The tension in the three cables create F1=200 lbf, F2=250 lbf, and F3=100 lbf with 0 = 30 degrees and p=24.1 degrees. If the eye bolt is in equilibrium, what is the x-component of the sum of other forces on the bolt (force from the nut and plate on the bolt) ? If you add up the three force vectors, the sum other force you are looking for will just be in the opposite direction to put the eye bolt in equilibrium. The x-direction is positive to the right. For example, if you find the sum of forces 1, 2, and 3 are 100 Ibf to the right, then the other forces in the x-direction must be pointing to the left (-100 lbf) to put the eye bolt in equilibrium. Eye bolt 2steel 3 plate Nut t Wonsher