During the push-off phase of a running stride the ground reaction force under the 1" metatarsal was measured to be 900.95 N at 30°. At this instant the triceps surae (gastrocnemius-soleus complex) is pulling on the calcaneus with a force of 1,222.75 N at an angle of 65°, and the tibialis anterior muscle is pulling with a force of 484.33 N at an angle of 60° on the medial cuneiform bone. The mass of the runner is 62 kg. Assume that the foot is a single rigid body, no other ankle musculature is active and the system is static. NOTE: All angles are reported relative to the right horizontal. Complete the free-body diagram of the foot shown below. a. What is the net horizontal talocrural joint reaction force? b. What is the net vertical talocrural joint reaction force? c. What is the magnitude of resultant taloCTural joint reaction force? d. What is the orientation of the resultant talocrural joint reaction force relative to the right horizontal?

During the push-off phase of a running stride the ground reaction force under the 1" metatarsal was measured to be 900.95 N at 30°. At this instant the triceps surae (gastrocnemius-soleus complex) is pulling on the calcaneus with a force of 1,222.75 N at an angle of 65°, and the tibialis anterior muscle is pulling with a force of 484.33 N at an angle of 60° on the medial cuneiform bone. The mass of the runner is 62 kg. Assume that the foot is a single rigid body, no other ankle musculature is active and the system is static. NOTE: All angles are reported relative to the right horizontal. Complete the free-body diagram of the foot shown below. a. What is the net horizontal talocrural joint reaction force? b. What is the net vertical talocrural joint reaction force? c. What is the magnitude of resultant taloCTural joint reaction force? d. What is the orientation of the resultant talocrural joint reaction force relative to the right horizontal?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Fi F2 H2 Fi F2

Q: Two forces act on a massless block. If the force FA is known, what must the magnitude of F3 be in…

A: If the block is not rotating about point P that means net moment about point P will always be zero.

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A: Given:The mass at the point A is the mass at point B is The mass of member OC is the mass of member…

Q: You may consider the biceps muscles tension to be completely canceled at the shoulder to which they…

A: Consider the free body diagram shown below for the given arm.

Q: 1) Determine the clamping force exerted on the smooth pipe B( NB) Express your answer to three…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: in the truss below, the maximum force(s) will occur in members GF, AF, or AB. What component…

A: In the truss below, the maximum force(s) will occur in members GF, AF, or AB.What component sustains…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

Q: During a drilling operation, the small robotic device is subjected to an (800 N) force as shown.…

A: Given: The Applied force's magnitude=800 N To find: The equivalent force couple system at the point…

Q: Determine the horizontal and vertical component of the force of the pin joint at F (kN)? Determine…

Q: Determine the force in member CA. Express your answer to three significant figures and include the…

A: Given: To find: Forces in all members

Q: 4e. If the two forces are F1=(3i-2j-9k) kN and F2=(-16i) kN, Find out All the correct equations…

A: F1=(3i-2j-9k) kN F2=(-16i) kN As per guideline, I can solve 1 question at a time . So ,please…

Q: 1. Find the forces in the members S2, S6 og S11. 2.By applying a horizontal force F4F_4F4 at point…

Q: 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force…

A: The force applied to the handle is, P=100 N Length of the handle is, L=30 cm

Q: In analyzing the unknown forces acting on a given pin in a plane truss, obtaining a negative answer…

A: Option 3 is correct The direction that was chosen for the force was incorrect, and the correct…

Q: he 15-lb bar BC is connected to a disk centered at A, and to a bar DC. If the disk is made to rotate…

A: Given data as per the question weight of BC bar =15 lb Length of BC =30 in

Q: B. 4 in 6 in 8 in 20 in 3 in X The model airplane shown above is supported by a single fixed support…

A: Given: The concentrated load at point A is FA= 4 lbs, The concentrated load at point B is FB= 2…

Q: For the system shown (for the extension strokes of the cylinders), what pump pressure is required if…

A: The pump pressure required: P = 424.4132 psi

Q: 4. Solve for all the force values of each member in the given system. 3 D 5 12 A W = 200 # 3 B

Q: why does the force exerted from AB to the hydraulic cylinder decrease "exponentially" as the angle…

A: Given-Data:- Load, W = 120 kNAB = 1.3 m To-Determine:- Force exerted from AB to the hydraulic…

Q: 6. Determine the force in each cable needed to support the flowerpot whose weight is 10ON とれ В 6 m 4…

A: The position vector is used to describe the location of a body. When it comes to characterising a…

Q: For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

During the push-off phase of a running stride the ground reaction force under the 1* metatarsal
was measured to be 900.95 N at 30°. At this instant the triceps surae (gastrocnemius-soleus
complex) is pulling on the calcaneus with a force of 1,222.75 N at an angle of 65°, and the
tibialis anterior muscle is pulling with a force of 484.33 N at an angle of 60° on the medial
cuneiform bone. The mass of the runner is 62 kg. Assume that the foot is a single rigid body, no
other ankle musculature is active and the system is static. NOTE: All angles are reported
relative to the right horizontal. Complete the free-body diagram of the foot shown below.
a. What is the net horizontal talocrural joint reaction force?
b. What is the net vertical talocrural joint reaction force?
c. What is the magnitude of resultant talocnural joint reaction force?
d. What is the orientation of the resultant țalocrural joint reaction force relative to the
right horizontal?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Statics of Rigid Bodies
1(a)An equivalent force-couple system will provide the same translation and rotational acceleration (or lack thereof) to a rigid body and the original force-moment system. We cannot say whether the internal forces in that rigid body are the same as for the original force system. Group of answer choices True False (b) It is always possible to reduce a system of forces and couple moments acting on a rigid body to a _____. Group of answer choices single force single moment single force and two moments single force and single moment
Two forces act on a massless block. If the force FA is known, what must the magnitude of F3 be in order to keep the block from rotating about point P. B A. FB = 3/5 FA B. FB = 3/4 FA C. FB = FA D. FB = 4/3 FA E. FB = 5/3 FA F P 4 m FB 3 m
A window cleaner is pulling himself up to a pulley that consists of two disks welded together as shown. The person is currently pulling straight down on the rope in his hands with a force of magnitude 580.4 N. The other rope is also vertical and is attached to the person's center of mass. The person's mass is 74.2 kg, the pulley's total moment of inertia is 395 kgm2, the radius of the small disk is 0.39 m, and the radius of the big disk is 0.73 m.What is the magnitude of the acceleration of the person's center of mass?
25.