Q18 Moving coil used in a PMMC voltmeter of (0-300V) has a depth of 3 mm and a width of 2.5 cm. With 100 number of turns the coil spreads flux at a density of 10 mWb/m?. The voltmeter has an internal resistance of 10 ohms. Then, i. Calculate the Control torque produced by the coil, when it is set to measure 250V. ii. Estimate the spring constant of the spring used, when pointer makes 30° deflection for the measurement of 120V. iii. Mention the consequence when control torque produced is more than deflection torque in a PMMC instrument.

Q18 Moving coil used in a PMMC voltmeter of (0-300V) has a depth of 3 mm and a width of 2.5 cm. With 100 number of turns the coil spreads flux at a density of 10 mWb/m?. The voltmeter has an internal resistance of 10 ohms. Then, i. Calculate the Control torque produced by the coil, when it is set to measure 250V. ii. Estimate the spring constant of the spring used, when pointer makes 30° deflection for the measurement of 120V. iii. Mention the consequence when control torque produced is more than deflection torque in a PMMC instrument.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q7/ A separately excited DC motor has the following parameters: Ra = 0.3 2, Ke = 0.52 V/rpm.Wb, d (flux per pole) = 150 mWb. The motor speed is controlled by a full wave bridge 'rectifier. The firing angle a is set at 30°, and the average speed is 1500 rpm. The applied a.c. voltage to the bridge is 440 V at 60 Hz. Assuming the motor current is continuous; calculate the armature current drawn by the motor and the steady-state torque for the cases of: (a) half-wave converter (b) Fully- controlled bridge
Can you solve the question ?
Colve asap
If the average pole flux of a dc machine with 24 coils, each of which contains 16 windings, 4 poles, double layered parallel winding (duplex lap winding), with a speed of 1000 rpm, is 15mWb, what is the idle winding voltage and (Note: In your operations, two digits after the comma) take it)
The purpose of a Yoke in a dc machine is to - a. collect the current b. provide protection c. increase output voltage d. convert induced voltage in to DC
The torque in AC machines depends on Select one: a. The strength of the rotor magnetic field b.The strength of the external magnetic field c.The sin of the angle between the rotor magnetic field and the external magnetic field d.A constant representing the construction of the machine e.All of above Clear my choice
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 45 degrees. The maximum RMS and average current ratings of the thyristor are equal to: Select one: O a. 33.94A and 21.6A O b. None of these O c. 24A and 10.8A O d. 48A and 26.09A Clear my choice
i need the answer quickly
Q9/ Complete the blank Commutator in DC machine is made up of .....................................?
A 600 V series motor takes 120 A and operates at 900 rpm when the load is80 HP. If the effective circuit resistance is 0.20 ohm, calculate the HPoutput of the motor when the current drops to 90 A. assuming that the fluxis reduced by 20 %. [Ans. 49.86 HP]
S. 8
6. In relation to a compound d.c machine, choose the right statement from the following (A) Both series and shunt field coils have comparable and number of turns and cross sectional areas. (B) Shunt field coil has fewer number of turns and large cross sectional area compared to series field coil. (C) Series field coil has fewer number of turns and large cross sectional area compared to shunt field coil. (D) None of (A), (B) and (C) are correct statement.