Q13/ For 555 astable multivibrator, if C = 0.01 µF, RA = 10 kn, RB = 50 kn, the frequency and the duty cycle will be nearly ---- --? Q13/ For 555 astable multivibrator, if C = 0.01 µF, RA = 10 k2, RB = 50 k2, the frequency and the duty cycle will be nearly -------------? +8 V kn 7 2 6 0.01 DF Oa) 1.6 kHz and 54.5% Ob) 1.3 kHz and 54.5% c) 1.6 kHz and 46.5% Od) 1.3 kHz and 46.5% RB kn 8 555 4 3 Vout

Q13/ For 555 astable multivibrator, if C = 0.01 µF, RA = 10 kn, RB = 50 kn, the frequency and the duty cycle will be nearly ---- --? Q13/ For 555 astable multivibrator, if C = 0.01 µF, RA = 10 k2, RB = 50 k2, the frequency and the duty cycle will be nearly -------------? +8 V kn 7 2 6 0.01 DF Oa) 1.6 kHz and 54.5% Ob) 1.3 kHz and 54.5% c) 1.6 kHz and 46.5% Od) 1.3 kHz and 46.5% RB kn 8 555 4 3 Vout

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In a 9 bit DAC using binary weighted resistors, if the MSB resistors is 30KQ, the LSB resistor O a. 2560.00 O b. 7680.00 O c. 15360.00 O d. 512.00
Using two synchronous counters 74161 to design a modulus-73 counter with clear input.
Vcc= 2.5 V 2 k2 600 2 2 k2 C3 VinoHHW Vout ㅇ 200 2 50Ω ERE1 C2 3) Indicate whether there is a phase shift between the input and output 4) Is the output inverted? 5) What do you think this circuit is doing? 6) Measure the voltage of VBE for the two transistors – are they operating in forward active region?
3- How many 74LS00 NAND gate inputs can be driven by a 74LS00 NAND gate outputs Refer to data sheet of 74LS00, the maximum values of IoH = 0.4 mA, IoL = 8 mA, IH = 20 µA, and In = 0.4 mA.
4. For the ripple counter in Figure 9-66, show the complete timing diagram for sixteen clock pulses. Show the clock, Qo, Q₁, and Q₂ waveforms. CLK FIGURE 9-66 D₂ ·lo D₁ •Q₁ Q₁ D₂ ·0₂ ē,
Consider the Moore machine shown in below figure.Construct the transition table. What is the output for input 01010? (0/0) 1/0 Output = 0 9 0/0 1/0 1/0 1/1 9:J0/0) Output = 0 Output 0/1 Output = 1
these. 5. To rotate a stepper motor which has 3 main terminals in counter clockwise dual full step with 8 cycles, the following data should be sent to the system. A. DAT DB 24H DUP(3H, 5H,6H) D. DAT DB 1CH DUP(3H, 5H,6H) B. DAT DB 24H DUP(6H, 5H,3H) E. DAT DB 08H DUP(3H, 5H,6H) C. DAT DB 1CH DUP(6H, 5H,3H) F. None of these. 6. What is the voluo of ID
3-In CMOS gates, what occurs when the frequency of the input signal increases: A) The power dissipation increases B) The fan out increa ses C) The power dissipation decrea ses D) None of the given Options E) Both power and fan out increase
Draw the Moore machine state diagram with minimal states for the digital alarm clock system(both of time set and alarm set)
Refresh rate is measured in hertz explain?
Commercial grade ICs can operate from a temperature range of -55 degree Centigrade to +125 degree Centigrade . Select one: True False
7. Determine Vo for the circuit in figure below, with 10V on both inputs. Si D D R1 ka E- 10 V 8. Determine Vo for the configuration in figure below; Ge 22 kn