Q1. The following data refer to the O.C.C of a D.C separately excited generator at 1000 rpm. Field current in A 0.2 0.4 0.6 0.8 1 1.2 Amature voltage in V 75 100 145 178 195 204 The machine is now connected as a shunt generator with a total field resistance of 200 and driven at 1000 pm. Estimate graphically: (i) the voltage to which the generat or will build up at no load. (ii) the armature, field and load currents when the teminal voltage is found to be 150 V. Neglect the effect of armature reaction and brush drop and assume armature resistance Rato be 0.8 2 (ii) Finally estimate the steady state armature curent when the machine terminals are shorted.

Q1. The following data refer to the O.C.C of a D.C separately excited generator at 1000 rpm. Field current in A 0.2 0.4 0.6 0.8 1 1.2 Amature voltage in V 75 100 145 178 195 204 The machine is now connected as a shunt generator with a total field resistance of 200 and driven at 1000 pm. Estimate graphically: (i) the voltage to which the generat or will build up at no load. (ii) the armature, field and load currents when the teminal voltage is found to be 150 V. Neglect the effect of armature reaction and brush drop and assume armature resistance Rato be 0.8 2 (ii) Finally estimate the steady state armature curent when the machine terminals are shorted.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A dc shunt generator has a critical field resistance of 400 Q2 at 1200 rpm. Now if the speed of the generator is increased to 1800 rpm what is the change in the critical resistance?
A shunt DC generator has no load terminal voltage of 140V. Armature resistance is 1ohm and shunt field resistance is 50ohm. Calculate the induced voltage.
1A. Which of the following is/are a method of providing field excitation for a DC generator. a) separately excited shunt b) self-excited series c) self-excited shunt d) all of the above 1B. Which type of field winding typically has the higher resistance? a) series b) shunt
Q1. The following data refer to the O.C.C of a D.C separately excited generator at 1000 rpm. Field current in A 0.2 0.4 0.6 0.8 1 1.2 Amature voltage in V 5 75 100 145 178 195 204 The machine is now connected as a shunt generator with a total field resistance of 200 Sn and driven at 1000 rpm. Estimate graphically: (i) the voltage to which the generat or will build up at no load. (ii) the armature, field and load currents when the teminal voltage is found to be 150 V. Neglect the effect of armature reaction and brush drop and assume armature resistance Rato be 0.8 2. (iii) Finally estimate the steady state armature curent when the machine terminals are shorted.
the armature of a 12 pole wave wound dc shunt generator has 50 slots with 12 conductors per slot. the generatoris running at a speed of 625 rpm and supplies a resistive load of 15 ohm at a terminal voltage 350v. the armature and the field reisitance are0.5 ohm and 70 ohm respectively. find the armature current,generated emf and flux per pole
q10
The current generated by the waterwheel generator changes direction as the wheel rotates, that is, it is an alternating current. Could you design a simple generator like this that would induce a current that continuously flowed in one direction (a DC current)? If not, explain why not. If so, describe and sketch your model solution below.