Q1. A compound bar consists of a circular rod of steel of 25 mm diameter rigidly fixéd Into a copper tube of internal diameter 25 mm and external diameter 40 mm as shown in Fig. Below. I the compound bar is subjected to a load of 120 kN, find the stresses developed in the two materials. Copper tube Steel rod SPARKA

Q: 100NM rod-1 100N rod-2 toost took 0.75 0.50 rod-1 0. rod-2

A:

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: The stresses acting on element A in the web of atrain rail are found to be 40 MPa tension in the…

A: Given   Stress =  40 MPa tension             = 160 MPa compression Shear stress = 54 MPa Find…

Q: Problem 7-6 A long hollow cylinder is of 20 cm external diam- eter and is 5 cm thick. It is…

A: A long hollow cylinder with an outward diameter of 20 cm and a thickness of 5 cm is known.It rotates…

Q: A rigid bar ABC is pinned at A and is connected by a steel bar CE and a copper bar BD as shown in…

A:

Q: A steel bar with a diameter of 100 mm is rigidly attached to the wall and carries the loads shown in…

A: Given: The diameter of shaft, d = 100 mm = 0.1 m The torque acting on the shaft, T = 8 kN.m The load…

Q: A 10 kN post is applied to the fixed-supported steel post as shown in the fig The post has a…

A: GivenFZ=10 kNNote - post diamter 100m too much large as compare to its length 1.5m. It must be 100mm…

Q: S A- Sección 4-a 1200 N B 1500 N 1000 N

A:

Q: least factor of safety if the material is cold-d

A: Sfhh

Q: (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the…

A:

Q: A tube of A-36 steel (Ea 200 GPa) is fixed at A and filled wi GPa). The outer diameter of the tube…

A: GivenEst=200GPaEcon=29GPado=20cmdi=15cmP=20kN

Q: Design a knuckle joint to two connect two co-axial steel rods with 45C8 (S= 380 N/mm) to support a…

A: given data

Q: As illustrated in Figure 1, the rectangular bar with dimensions of 250 mm by 400 mm is subjected to…

A:

Q: Find the stresses that will occur in steel and copper when the system is heated with a temperature…

A: The diameter of the solid copper rod is, Dc=20 mm The expansion coefficient of the solid copper rod…

Q: 3. Work problem 2.9-2 from the textbook, which is as follows. The prismatic bar in the figure is…

A:

Q: (Ans, 49.1 MP Steel L- 0.9 m A-300 mm? E-200 x 10° N/m2 a11.7 um/(m°C) Aluminum L 1.2 m A = 1200 mm?…

A: Deflection in steel rod due to temperature is δTst=αL∆T=11.7×10-690040=0.4212 mm Deflection at point…

Q: In the figure, a solid copper rod with an expansion coefficient aB = 165.107-1 / °C is 20 mm in…

A: To find: The stresses induced. Given: The diameter of the copper rod is dcu=20 mm1 m1000 mm=0.020 m.…

Q: A thick-walled cylinder with internal and external radii 86 mm and 166 mm respectively, is subject…

A: we have to determine the radial and hoop stress

Q: Q1/ A two circular bars of brass (AB) and steel (CD) in horizontal state with gap of (1.5min)…

A:

Q: In the figure, a solid copper rod with an expansion coefficient αB = 165.10-7 1 / ° C is 20 mm in…

A:

Q: Figure 1: This bar is made of AISI 1020 cold-drawn steel and is loaded by the forces F=60 lb, F2= 80…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Q4 (a) A thin eylinder 95 mm internal diameter, 500 mm long with walls 4.5 mm thick is subjected to…

A: The cylinder, as mentioned, is assumed as a thin shell. The internal pressure in a thin shell…

Q: P solid, see Fig below. The outer diameter of the hollow and solid sections is 6 cm and the inner A…

A: Given: The outer diameter of the solid and hollow section: →Do=6 Cm=0.06 m The inner diameter of the…

Q: A wire of circular cross-section of diameter 1.0 mm is bent into a circular are of radius 1.0 m by…

A:

Q: Q2: Figure (2) shows an isometric view of a crankshaft that is actuated by the vertical force acting…

A:

Q: Bronze A = 300mm² E = 83 GPa 2.00 m %3D Steel A = 600mm? E = 200 GPa 1.00 m A 0.60m 1.00 m 1.00m

A:

Q: A cast aluminum cylinder of a portable hydraulic riveter is d 210mm in diameter. The pressure of the…

A:

Q: The horizontal steel rod, 2.5 m long and 1200 mm² in cross-sectional area, is secured between two…

A:

Q: Problem #3. The figure below are cables ( circular section) supporting a 36 kN. Find the axial…

A:

Q: The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the…

A: Given Data Weight of bar is : w1=5 kN/m Load applied is : W=150 kN Temperature change is : ∆T=20°C…

Q: A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force…

A:

Q: A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown in…

A:

Q: 2. A 3-m long bronze bar with a cross-sectional area of 350 mm? is secured between two rigid walls…

A: GivenL=3m=3000mmA=350mm2T1=15oC∆=3mmα=18×10-6 /oCE=80Gpa

Q: The Mohr's circle for a point near the base of a traffic pole is shown below. the center of the…

A: Consider the diagram shown below for the given Mohr’s circle.

Q: Find the smallest diameter for the one bolt that can be used in the figure if P = 90 kN. The working…

A: The given figure shows a single riveted joint with double plate  To find :  the area of the bolt…

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

A: