Q1: Two diodes are required to handle a source voltage of 8kV with I-V performance shown below... 1. How these diodes can be connected to handle the source voltage? 2. If they are required to handle equally voltage, how much will the sharing resistances be ? if Rs1=90% Rs2. Find the values of Rs1 & Rs2 3. The obtained voltages across the diodes at equally shared resistances of 50k Ohm. while the currents are 40 mA and 50 mA respectively. Diodes' I-V curve ID DI D2 SkV 6kV 4kV 50mA 60mA VAK

Q1: Two diodes are required to handle a source voltage of 8kV with I-V performance shown below... 1. How these diodes can be connected to handle the source voltage? 2. If they are required to handle equally voltage, how much will the sharing resistances be ? if Rs1=90% Rs2. Find the values of Rs1 & Rs2 3. The obtained voltages across the diodes at equally shared resistances of 50k Ohm. while the currents are 40 mA and 50 mA respectively. Diodes' I-V curve ID DI D2 SkV 6kV 4kV 50mA 60mA VAK

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Four diodes and one Zener diode are connected to form the circuit below. a) Describe how a single diode behaves when forward biased. 5) draw the output as the input changes from -12 V to +12 V. Assume that all diodes can be represented by a constant-voltage of 0.6 V (in forward bias) and the Zener diode has a breakdown voltage of 6.8 V. d) What is the function of the circuit? Suggest a proper application. I kN Da Dr
A half wave rectifier circuit with a 1K ohm load operates from a 120V rms 60-Hz household supply through a 10-to-1 step down transformer. It uses a silicon diode that can be modeled to have a 0.7V drop for any current. What is the peak voltage of the rectified output? For what fraction of a cycle does the diode conduct? What is the average output voltage? What is the average current in the load? Thanks for any help.
a) What is n-type semiconductor materials? What are the majority and the minority cariers? b) What is p-type semiconductor materials? What are the majority and the minority cariers? c) What is depletion region of a p-n junction diode? d) Describe in your own words the forward-bias and reverse- bias conditions of a p-n junction diode. e) Draw a Diode Symbol and label the anode and the cathode. Si Ge 2 ka f) Find V, in the circuit shown in +20 V 2 k2 15V Fig. Fuad Al-Mannai EENG261 Page 1
Answer all the items. Thanks!
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
I need help quickly please
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
quick reply needed.
24 A M0-volt forwurd voltage is applied to a silicon diode in series with a load of 3 k2. Draw the de kud line. What is the slope of the line? Solution The value of voltage Vy across diode is given by Vy V-R Since R and V are fixod values, this equation can by represented by a straight line on V-ly characteristics of diode; the is de kud li. When lg 0, maximum voltage across the diode V 30 V. This is point B(30, 0). 10 mA 30 V Fig. 2.25 Problem 2.4.