Q1: The steel strap with thickness of 12 mm is to be we lded to a rigid frame to carry a static load of F=20 kN. The strap and frame are we lded together by fillet welds along two sides. Using the max imum distortion energy theory, determine the minimum length of the we ld to be on safe side. The yield strength is 420 MPa. The safety factor should be considered as 4. (k=12 mm)

Q1: The steel strap with thickness of 12 mm is to be we lded to a rigid frame to carry a static load of F=20 kN. The strap and frame are we lded together by fillet welds along two sides. Using the max imum distortion energy theory, determine the minimum length of the we ld to be on safe side. The yield strength is 420 MPa. The safety factor should be considered as 4. (k=12 mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

rectanqular seetion with width bz250 and depth h= 500mm is to carcry a A m %3D design bending moment M= 260KN•M, The conerete is of greade e30 and the tensile steel is of HRB400. The tension reinforzce. ment A, is requined.
11. Iwo beams, one having square cross section and another circular cross-section, are subjected to the same amount of bending moment. If the cross-sectional area as well as the material of both the beams are same then (A) Maximum bending stress developed in both the beams is the same (B) The circular beam experiences more bending stress than the square one (C) The square beam experiences more bending stress than the circular one (D) As the material is same both the beams will experience same deformation
r Two Example (2) 8- A compound bar is constructed from three.. wide by 12mm thick together to form a bar somm wide 30 The middle bar is of aluminum alloy for which F-70 GP= outside of brass with E-100 MPa. If the bars are initia at 18c and the temperature of the whole assembly is to to So C, determine the stresses set up in the brass and the Kg = 18 510 Solutions2 FB = FAL FB So*12*10 63 Ext. + Comp. = (XAI - XB) L.A.T. FB.L FAL.L AAL.EAL Ag Eg = DAL + From these equation & FAL=3984 N FB 1992. N 1992 50*121610-6 FB AB -6 XA => 22 *10°-=-=- = (XAL-XB) LAT FAL *100*109 So*12*10% 70 4109 FAL 3984 AAL SO#1210-6 SB = SAL How find that?! = 32. MPa (Ton) FAL. L AP EA = (22-18) x 10² (50-18) XIF_P=15 KN (camp.) Find O'B and GAL F₁+ 2FB = 15 6.64 MPa: (comp)... L FB.L AB. E.B ww.as 17 Brass AL Brass
A steel plate is used to connect a column and beam as shown in Fig. 3. The connection betweenthe beam and the plate is fillet welds. Given Q=150kN and Mx= -5kN-m (applied at centriod ofthe welds between the beam and the plate), determine maximum shear stress in the welds betweenthe beam and the plate.
1
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.
Given the compound bar below, determine the maximum allowable value of P if the change in length of the bar is limited to 5.67mm. The bar properties and allowable stresses are given in the table below. (answer in N)
Solve for joint @ A & C / AC