Q1: The 2-Mg truck achieves a speed of 15 m/s with a constant acceleration after it has traveled a distance of 100 m, starting from rest. Determine the normal force exerted on each pair of front wheels B and rear driving wheels A. Also, find the traction force on the pair of wheels at A. The front wheels are free to roll. Neglect the mass of the wheels Ans.: NB = 10729.3 N, NA = 8890.71 N traction force FA = 2250 N 0.75 m 2 m 1.5 m- B

Q1: The 2-Mg truck achieves a speed of 15 m/s with a constant acceleration after it has traveled a distance of 100 m, starting from rest. Determine the normal force exerted on each pair of front wheels B and rear driving wheels A. Also, find the traction force on the pair of wheels at A. The front wheels are free to roll. Neglect the mass of the wheels Ans.: NB = 10729.3 N, NA = 8890.71 N traction force FA = 2250 N 0.75 m 2 m 1.5 m- B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the minimum weight of block A in order for motion to be impending down the plane (to the left). Assume the pulley to be frictionless. Given:WB = 180 lbs, θ = 40 °, μ = 0.2 for all surfaces.
The 16-Mg truck hauls the 37-Mg trailer. If the unit starts from rest on a level road with a tractive force of 21 kN between the driving wheels of the truck and the road, compute the tension T in the horizontal drawbar and the acceleration a of the rig. Answers: T = a = i 37 Mg KN m/s² 16 Mg
Parvinbhai
3. A 5-kg crate is released from rest at Point A of a 20-kg ramp which is inclined at 40 degrees as shown in the figure below. The lengths of the ramp is 2 m. The interface between the ramp and the ground can be assumed to be frictionless. Use Newton's 2nd Law and the definition of the center of mass to determine the horizontal distance that the ramp has moved when the crate reaches Point B. Neglect the size of the crate. Does your answer depend on the frictional force between the crate and the ramp? e S
Please help with the attached problem.
The flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity w. Prior to rotation, each of the 0.52-kg sliding blocks has the position x = 28 mm with no force in its attached spring. Each spring has a stiffness of 430 N/m. Determine the value of x for each spring for a steady speed of 279 rev/min. Also calculate the normal force N exerted by the side of the slot on the block. The force N is positive if it pushes from the side labeled A. Neglect any friction between the blocks and the slots, and neglect the mass of the springs. (Hint: Sum forces along and normal to the slot.) Answers: X = wwwwwwww N = i i -74-74- mm mm mm N
Determine the tension P in the cable which will give the 79-lb block a steady acceleration of 4.1 ft/sec2 up the incline.
4. The vehicle is designed to combine the feel of a motorcycle with the comfort and safety of an automobile. If the vehicle is traveling at a constant speed of 80 km/h along a circular curved road of radius 100 m, determine the tilt angle 0 of the vehicle so that only a normal force from the seat acts on the driver. Neglect the size of the driver.
The uniform cylinder has a mass of 30.0kg and is rotating about a horizontal axis through O at 1200 rpm. The coefficient of kinetic friction between the cylinders and braking levers is 0.200. If the spring tension is 100 N, calculate the time required for the cylinder to stop spinning.
The electric motor is used to pull a train at a maximum constant speed of 60 km/h. This motor has a power of 340 kW. The train is pulled directly up the inclination of 1 in 180. The tractive resistance against the motion is 80 N.1.Draw the free body diagram representing all forces acting on the train2.Calculate the mass of the train.
Q5: The 15 kg cylinder rotates with an angular velocity of 40 rad/s. If a force F = 6 N is applied to the AB bar, as indicated, determine the time required to stop rotation. The coefficient of kinetic friction between the bar and the cylinder is 0.4. Disregard the thickness of the bar. F = 6N 400 mm- 500 mm B 150 mm-
Fial I The figure shows a body consist of two segments which are a rod AB and a disk with weights of 4-lb and 11-lb respectively. The body is attched with a spring. The roller 1 ft k = 8 lb/ft Datum at C allows the spring to remain vertical as the rod falls. B A The length of the unstretched spring is 0.85 ft. If the body is released from rest and rotates CW about point B, 1 ft 3 ft determine the following: (Assume the datum at point B) 0.25 ft 1. The potential energy of the spring when the body is horizontal. 2. The potential energy due to gravity when the body is horizontal. 3. The potential energy of the spring when the body is vertical. 4. The potential energy due to gravity when the body is vertical. 5. The angular velocity at the instant the body becomes vertical.