A 8 ft- -2 ft A beam that weighs 300 lbs is supported by a roller and pin B and A respectively while being subjected to force of 1000 lbs. If the pin at A is suddenly removed, determine the beams angular acceleration, the orce exerted by support Band the horizontal acceleration just after A is removed. Assume the beam is a lender rod of negligible thickness. Please don't use angle measurements when solving. Use the 3-4-5 triangle to solve, if that makes sense.

A 8 ft- -2 ft A beam that weighs 300 lbs is supported by a roller and pin B and A respectively while being subjected to force of 1000 lbs. If the pin at A is suddenly removed, determine the beams angular acceleration, the orce exerted by support Band the horizontal acceleration just after A is removed. Assume the beam is a lender rod of negligible thickness. Please don't use angle measurements when solving. Use the 3-4-5 triangle to solve, if that makes sense.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inverted crank-slider shown has crank AB 3 in and ground link AC = 6 in. Find the re-rocking angle AO, of rod 4 between its extreme right and extreme left positions. Write your answer in degrees but do not write the units. A C DELL
The crank AB rotates in the vertical plane with a constant clockwise angular velocity w0 . For the position shown calculate the force under the light roller C of the 10-kg slender bar BC w0=4.2 rad/s. Solve correctly please.
2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14. 25 kg. If the cord is pulled upward with a force T of magnitude 171 N, determine a. the acceleration of the center of the disk, b. the angular acceleration of the disk, c. the acceleration of the cord. T 0.5 m Go A Draw the Free Body Diagram.
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A uniform slender rod of length L = 900 mm and mass m = 4 kg is suspended from a hinge at C. A horizontal force P of magnitude 75 N is applied at end B. A Ja B C P Determine the corresponding angular acceleration of the rod. The corresponding angular acceleration of the rod is rad/s² O.
d I à B 8 rad k Ť You were able to obtain a roll of toilet paper during quarantine and put it to good use. If the roll rests against a wall where its coefficient of friction is -0.22 and you apply a force of 0.7 N at an angle of 40* from the vertical. Force F is also tangent to the roll. Determine the angular acceleration of the precious toilet paper. Mark a counterclockwise acceleration as positive and a clockwise acceleration as negative. Hint: Watch your vector direction for a above F Assume the roll can be treated as a cylinder with a mass of 0.21 kg, a width of 11.5 cm, and a radius of 7.5 cm. Point B is a vertical distance d=13 cm from point A. UBC Engineering
The motor lifts the 40-kg crate with an acceleration of 6 m/s2 as shown in (Figure 1). Part A: Determine the x and y components of force reaction at the fixed support A using scalar notation. Express your answers in newtons to three significant figures separated by a comma. Part B: Determine the couple moment at the fixed support A. Express your answer in kilonewton meters to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise.
The uniform 50-kg sphere has radius r = 0.2 m and is welded to the center of the uniform 30-kg shaft as shown. When a constant couple moment M is applied to the shaft, its angular velocity reaches 74 rad/s after 4 s. Determine the magnitude of the moment M. Write your answer in N.m but do not write the units. M R= 0.1 m Taylor e m Te am Answer: Answer
Problem: 15 (of 30) Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your units. The uniform square steel plate has a mass of 12 kg and is resting on a smooth horizontal surface in the x-y plane. If a force P= 110 N is applied in the x-y plane to one corner in the direction shown, determine the magnitude of the initial acceleration of comer A. Hint: At the initial stage of motion when the plate begins to move, w= 0 because the plate is barely moving. a of A = 9 m/sec^2 A 500 mm P 500 mm 30° Check Answer for this Problem Close
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. B 500g 400 mm 400 mm
The 490-lb beam is supported at A and B when it is subjected to a force of P = 1000 lb as shown. 8 ft -2 ft- Part A If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be neglected. Express your answer to three significant figures and include the appropriate units. You did not open hints for this part ANSWER: a = Part B Determine the force of the roller support on the beam. Express your answer to three significant figures and include the appropriate units. You did not open hints for this part ANSWER: By =
EXERCISE 3.40 Collar C slides relative to the curved rod at a constant speed u. The rotation rate about bearing axis AB is constant at Q. Determine the acceleration of the collar in terms of the angle locating the collar. Also derive expressions for the dynamic forces exerted on the collar by the rod and the tangential force required to hold u constant. Gravity may be assumed to be unimportant. (Hint: attach frame xyz to the curved rod, make the tangent point of AB and circle as its origin. Axis x is horizontal and rightward. y axis is vertical and downward.) 225