Q1): Reinforced concrete floor with 6* 7 m span C/C as shown below in Fig. (1). The live load 3 KN/m², the superimposed load (partition loads) is 2 KN/m² and the floor finish load is 2.5 KN/m². fc-21 MPa, fy -380 MPa. The column dimension 300* 300 mm and the supporting beams are 300mm width by 800 mm depth. (Using Method 3 for A & B), A- Design of slab (S1) and showing the reinforcement details. B- Find the Design Load of B1, B2 and 83 Note: For slab Use bar diameter - 12 mm. $12 Fig. (1) E BA E

Q1): Reinforced concrete floor with 6* 7 m span C/C as shown below in Fig. (1). The live load 3 KN/m², the superimposed load (partition loads) is 2 KN/m² and the floor finish load is 2.5 KN/m². fc-21 MPa, fy -380 MPa. The column dimension 300* 300 mm and the supporting beams are 300mm width by 800 mm depth. (Using Method 3 for A & B), A- Design of slab (S1) and showing the reinforcement details. B- Find the Design Load of B1, B2 and 83 Note: For slab Use bar diameter - 12 mm. $12 Fig. (1) E BA E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

reinforced Concrete
A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
The beam is simply supported on a span of 6 m and carries a load of 18 KN/m. Use ACI Specifications withfc’ = 17.2 MPa, fs = 124 MPa, n = 12, d’ = 65 mm, and ?concrete = 23.54 KN/m3.(a) service moment (f) use b = 250 mm, d = Answer (round down to nearest 25 mm) + 50 mm(b) fc to take care of dead load(c) k (g) h (h) dead load (i) total load(d) j (j) recompute service moment (k) check effective depth(e) R (l) use 28mmɸ for As (m) check main bar clear spacing
SITUATION A: The floor system shown has the following applied loads. Super Imposed Dead Load = 2.00 kPa Live Load = 1.90 kPa Slab Thickness = 100.00 mm Weight of Concrete = 24 kN/m3 Self-Weight of the beam = 1.92 kN/m Material Specifications: f’c = 21.00 MPa fy = 345.00 MPa Steel Cover = 50.00 mm What is the maximum positive moment of beam BE, acting on the midspan? in kN-m What is the maximum steel ratio of the section located at the supports? What is the actual steel ratio of the beam section at the supports? What is the ultimate moment capacity of the beam at the supports? in kN-m What is the effective flange width at the midspan? in mm What is the height of the compression block of the section at midspan? in mm What is the ultimate moment capacity of the beam at the midspan? in kN-m What would be the height of the CHB that can be placed on beam BE? Assuming the weight of the blocks is 2.30 kN/m per meter height? in meters
I need the answer to the question in reinforced concrete
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
Principle of Reinforced Concrete Design
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a service live load of 2.1 kPa. Using f.-21 MPa, rebar strength f, 415 MPa, calculate the following if a typical interior beam is reinforced with 3- 16-mm-dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. Nominal moment capacity (kN-m) of a typical interior beam in positive bending considering T-beam geometry. A. 96.66 C. 91.10 Maximum factored uniformly distributed load (kN/m) a typical interior B. 86.99 D. 81.99 2. beam can sustain against positive bending. В. 27.83 с. 26.23 D. 29.15 A. 30.93 3. Maximum service superimposed dead load in kPa. A. 17.73 C. 16.52 B. 11.08 D. 14.77
4.3 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____?____ kN/m (to the nearest whole number)