Q1// long shunt compound generator supplies 600 KW, 1200V shunt fieldresistance =75 0, armature resistance%-D0.030, commutating field windingresistance=0.0112, series field resistance=D0.0120, divertor resistance=0.036N, at60 r.p.m. determine the percentage increase in flux per pole required to generate1600 V at 40 r.p.m.

In the question, Consider a long shunt dc Generator i. e shunt winding connected to the after…

Q1// long shunt compound generator supplies 600 KW, 1200V shunt field resistance =75 0, armature resistance%-D0.03N, commutating field winding resistance=0.0110, series field resistance=D0.0120, divertor resistance=0.0362, at 60 r.p.m. determine the percentage increase in flux per pole required to generate 1600 V at 40 r.p.m.

Q1// long shunt compound generator supplies 600 KW, 1200V shunt field resistance =75 0, armature resistance%-D0.03N, commutating field winding resistance=0.0110, series field resistance=D0.0120, divertor resistance=0.0362, at 60 r.p.m. determine the percentage increase in flux per pole required to generate 1600 V at 40 r.p.m.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please solve this problem step by step and illustrate your answer properly. Write your answer in a piece of paper please. Box the final answer.
An engineer is designing 4-pole DC generator with 30 conductors by using simplex two-layer wave- winding method. Sketch the armature winding by showing the proper calculations.
The series field winding of a 170 kW, 250 V, 1450 rpm compound generator has a resistance of 0.00306 ohm. What will be the required resistance (in Ohm) of a noninductive diverter that will bypass 27 percent of the total armature current? "
A shunt DC generator has no load terminal voltage of 140V. Armature resistance is 1ohm and shunt field resistance is 50ohm. Calculate the induced voltage.
Please see attached picture
1A. Which of the following is/are a method of providing field excitation for a DC generator. a) separately excited shunt b) self-excited series c) self-excited shunt d) all of the above 1B. Which type of field winding typically has the higher resistance? a) series b) shunt
A 4 pole generator with wave wound armature has 52 slots each having 22 conductors. The flux per pole is 0.01 Wb. (i) At what speed must the armature rotate to give an induced EMF of 220V is, (ii) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
(a) A 6 pole generator with lap wound armature has 135 slots each having 14 conductors. The flux per pole is 20 mWb. At what speed must the armature rotate to give an induced EMF of 210V. (b) What will be the voltage developed, if the winding is wave connected and the armature rotates at the same speed
short shunt compound generator delivers a load current of 10A at 200V and has a shunt field resistance 200 ohms. The shunt field current of 2A. Then armature delivers a current of a.10A b.8A c.11A d.12A
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
The shunt field winding of a shunt generator has a resistance of 80ohms at 20 degrees Celsius. After several hours of continuous operation, the winding temperature rises to 50 degrees Celsius. How much is the winding resistance under this condition. Assume the resistance temperature coefficient of copper to be 0.004 ohm per degree at 0 degree Celsius. *
A 4 pole generator with wave wound armature has 56 slots each having 28 conductors. The flux per pole is 0.01 Wb. (i) At what speed must the armature rotate to give an induced EMF of 230V is, (ii) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,